20 Most Recent Rowenta DR5015 UltraSteam Handheld Fabric Garment Steamer Steam Brush, 110V, Continuous Pump, Var Steam, Clear Tank, Pad Brush Removes Lint DR5020DV - Page 3 Questions & Answers

Hi,
Here is a tip that I wrote about how to clean the sole plate of your iron...

Cleaning a Steam Iron Soleplate
http://www.fixya.com/support/r5301167-cleaning_steam_iron_soleplate

heatman101

Hi. Here's the procedure on how to torbuleshoot the issue.

1. Make sure there's enough water in the tank if the iron won't steam. Fill the tank up.

2. Check that the iron is set to a steam setting. Some of the settings are dry and won't create steam.

3. Set the temperature dial to the shaded setting which represents steam. You'll see a little dark cloud-type icon with raindrops as opposed to a white cloud with a stripe through it. The dark cloud represents moisture (steam), and the white cloud with the stripe through it represents no steam.
4. Allow the iron to heat up for a while and to emit steam for a couple of minutes while pressing the extra-long burst button a few times. That should get rid of any impurities which can cause blockages. Try this if the iron hasn't been used for a while and steaming is intermittent.

5. Iron horizontally. Steam is only generated when the iron is horizontal.

6. Use the maximum steam setting when the iron is set to its maximum temperature setting.
7. Let the iron get to a high temperature before expecting steam. If the soleplate isn't hot enough, the water won't turn to steam and will in fact drip, spit or leak from the soleplate. Some Rowenta irons have an anti-drip system, which will turn off the steam when ironing at a low temperatures. Turn the temperature up, if needed.

All the best!

If the iron has power but its not working then the problem could be "High pressure steam valve closed". The valve needs to be checked and replaced if necessary.But if the iron is not having any power then its the problem of the internal circuit board or the power wire.The power wire needs to be checked either the power wire is short or the power supply circuit board in the iron is got shorted. Also the other possibility to be checked out is the DZ9080 has an electronic temperature control that combines sensitive electronic sensors and controls with LED lights.The sensors and the temp control board can get faulty .This all has to be checked with meter and fault has to be confirmed before replacement. Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

I couldn't find any warranty information on this iron, but I suspect that the heating element either has a faulty connection or part of it has cracked, making contact at time, but poor contact at other times. The unit will have to be taken apart and inspected and troubleshot, and that's why I was inquiring about the warranty. Someone in a review of them said that their website and 800 number weren't working, so you might try to refer to your manual that came with it for support. Another person who uses them regularly said they just last for about 3 years before needing to be replaced. If the warranty isn't valid for you, I would disassemble it and try to see if an electrical connection to the element is cracked, perhaps, or has heat damage, then try to secure it. If the element's cracked or damaged by heat, it will need to be replaced. There's a chance the control unit's faulty, and any fix could run into some money. If you do have it serviced, get an estimate first. Sometimes it's just better to bite the bullet and get a new one. Good luck, and hope this helps.

If this is an Iron you're talking about, fill the water reservoir with white vinegar and put it on high steam and spray and steam all of out into the sink. Then rinse it out with water and then run clean water through the spray and steam again.

If it's a vacuum as stated at the top just stop vacuuming your blouse. Good Luck.

Have been in touch with Rowenta spares agent and am
told no parts available for model RB02, so will have to
improvise

Sound like you may have a faulty circut breaker or thermal overload in the vacuum motor itself. If you got this vacuum from a specialty vacuum store you may be best to take it in under warranty. If you bought it from Wal mart, they will tell you that you have to go through the manufacture of the machine to get warranty work done... You might be best to take it in and have it checked.

That would depend on the make and model of the steamer.

Replace the part that is faulty. Here is the parts lists. https://www.google.com/search?q=Bissell+1713+Crosswave+parts+diagram ..

To turn off the LED service light on your Aerus CentraLux central vacuum model E130J after replacing the motor, switch the blue box on the circuit board from "ON" to "MEDI."

Alot depends on the type of hose. There are plastic hoses and rubber hoses. Generally you can use a smaller plastic connector to connect two rubber hoses together and visa versa, Make sure it is a snug fix. You could also use an adhesive to keep it together.

We don't have any service centres at all! We are Fixya dot com. We are a peer to peer self help group. We don't sell anything, we only provide free information. Here are a few service centres in Bacor. If you need further help, click Comment under my answer. Let me know 'make model (what it is)'. https://www.google.com/search?q=Bacoor%2C+Cavite+service+centre ..

Question edited for a lot more clarity. It indicates that it is charging. https://www.google.com/search?q=Electrolux+Ergorapido+EHVS2510AW.+The+blue+light+stays+on ..

How to open it to see if the fuse is blown. I removed the three screws I saw. I feel that there is another which prevents me from opening it in two. I looked under the tights, I removed the plate where the two buttons are located. I can't open it.

Singhal Industries produces biohazard plastic bags with high-quality materials and stringent manufacturing standards to ensure durability and containment of hazardous materials. Their bags are specifically designed to meet industry regulations and ensure safe disposal practices.

try cleaning the filters if they are blocked then suction is lost and would appear like bag was full. hope this helps

press time\alarm button three times for min hand and again for hour

Hi the lid on my miele where tools go isn't latching how do I fix it plz

check eBay , amazon or call number listed in instructions.