20 Most Recent
Dyson Air Multiplier 10" AM01 Bladeless Fan - Satin Iron/Blue - Page 9 Questions & Answers
How do I change belt on Model LD7600 dryer
To change the belt on your Model LD7600 dryer, follow these general steps for a safe and effective replacement:
1. Start by disconnecting the dryer from the power source to ensure your safety.
2. Access the dryer drum by removing either the top panel or front panel, depending on the design of your Model LD7600. Check your user manual or specific instructions for the correct method.
3. Remove the old belt by carefully releasing its tension and taking note of how it is routed around the pulleys. Then, remove it from the pulleys.
4. Install the new belt by looping it around the drum and ensuring it's positioned in the groove. Refer to diagrams or your user manual to ensure proper routing.
5. Check the belt tension. Adjust the tensioning mechanism as needed to ensure the belt is not too tight or too loose.
6. Reassemble the dryer by replacing the top or front panel and securely fastening all screws or clips.
7. Test the dryer by plugging it back in and running a dry cycle to ensure proper functioning.
Keep in mind that specific models may have slight variations in the replacement process. Always refer to your user manual or manufacturer's instructions for accurate guidance.
6/6/2023 9:50:21 PM •
Dryers
•
Answered
on Jun 06, 2023
Harbor breeze LGF-1
great question. The good thing is that in order to remove ceiling fan blades from a ceiling fan, the instructions are generally straight forward and generic. In most cases, you'll need to shut the power off at the breaker or the fuse panel and then use a Phillips screw driver head to remove the blades.
Here's an article that provides a good step by step on how to accomplish this task:
https://hampton-lighting.com/how-to-remove-ceiling-fan-blades/
5/14/2023 1:39:47 PM •
Dryers
•
Answered
on May 14, 2023
How to load belt on pulleys
All question need full 'make model (what it is)'. But we can guess.
The tensioner idler pulley is not providing enough tension or the pulleys have somehow come out of alignment. Or the belt has stretched. One further thing is drum bearings and slides creating too much resistance and causing the belt to jump.
4/18/2023 3:55:39 AM •
Dryers
•
Answered
on Apr 18, 2023
Which thermostats goes where in a creda simplicity tumble dryer
When it comes to installing a thermostat in a Creda Simplicity tumble dryer, it can be a bit of a tricky task. But don't worry, we've got you covered! Here's a step-by-step guide to help you get the job done quickly and easily.
First, you'll need to locate the thermostat. It's usually located on the back of the dryer, near the top. Once you've found it, you'll need to remove the screws that hold it in place.
Next, you'll need to disconnect the wires from the old thermostat. Make sure to note which wire goes where, as you'll need to reconnect them to the new thermostat.
Once the wires are disconnected, you can remove the old thermostat and replace it with the new one. Make sure to connect the wires to the new thermostat in the same order as before.
Finally, you'll need to secure the new thermostat in place with the screws. Once that's done, you're all set!
Installing a thermostat in a Creda Simplicity tumble dryer may seem like a daunting task, but with a few simple steps, you can get the job done in no time. Now that you're an expert, you can tell your friends: "I'm the thermostat whisperer!"
4/15/2023 10:34:45 PM •
Dryers
•
Answered
on Apr 15, 2023
I am looking for best Dry Cleaners & Tailoring Service providers in California?
I suggest Fazio for your ordinary cleaning needs, any customizing, and at whatever point you need something pivoted rapidly. I give two of pants for decreasing and sewing, let him know I required them the accompanying week, yet he did the work in a matter of hours. Quick as well as high caliber. Kept the original hem of my pants, looked great.
4/14/2023 7:41:06 AM •
Dryers
•
Answered
on Apr 14, 2023
Not finding what you are looking for?