Brinks 102-44831 Solid Steel Shrouded Padlock, 1-13/16-inch - Answered Questions & Fixed issues


use a master key the crow bar

21917287-t0rkdbdnr1a3xkqlooxh5z5n-1-0.jpg

Brinks Locks &... | Answered on May 02, 2016 | 266 views


Probally tap with hammer and open then oil it

Brinks Locks &... | Answered on Jul 02, 2015 | 304 views


www.rrbrink.com

Brinks Locks &... | Answered on Jul 01, 2014 | 97 views


Latch may be dragging. Tap/rap shake door after turning key.

Brinks Locks &... | Answered on Jul 01, 2014 | 80 views


Do you mean duplicates of keys or do you have no working keys?

Brinks Locks &... | Answered on Jun 23, 2014 | 330 views


If you have both pieces of the broken key, it can be duplicated.

I did not find that key code listed for Brinks, but perhaps you can get one from Brinks. A locksmith can make a key, check the cost. You really don't want to pay more than the cost of replacing the lock.

Brinks Locks &... | Answered on Jun 16, 2014 | 333 views


I think a local locksmith would either be able to make the keys or give you a reason why keys can not be made for your locks. Look up 'locksmith' in your local yellow pages.

Brinks Locks &... | Answered on May 23, 2014 | 961 views


Janice the part you are describing is called a snap ring, and it probably is intended to hold the knob assembly together. If you are feeling courageous, you could take the one that was assembled correctly off the door and see if you can locate where the snap ring is supposed to fit. Arguably this is a manufacturing defect, and as the product has a lifetime warranty, I would suggest contacting Brinks. Toll Free: 1-800-562-5625 Your product number is 2103-109.

Brinks Locks &... | Answered on May 20, 2014 | 89 views


Other than calling a locksmith, I'd suggest visiting this lock pickers forum.

See if anyone here can advise you before you spend money. Lock Picking 101 Forum for Lock Picking Locks Safes Picks and Locksmiths

Brinks Locks &... | Answered on Apr 28, 2014 | 218 views


I have this lock and forgot the pass code. It is unlocked and it has some kind of switch on the back of it. How do I reset ti? US. PAT 5746075 DE. PAT NO.M606494.3 Brinks Lock. Please email me at [email protected] .

Brinks Locks &... | Answered on Nov 08, 2013 | 2,522 views


It likely requires powdered graphite or white lithium grease to lubricate it back to its original condition... or else try WD40 though it tends to be a more temporary fix

Brinks Locks &... | Answered on Oct 15, 2013 | 113 views


THIS IS NOT SENTINEL WEBSITE TECH SUPPORT

Locks &... | Answered on Jul 07, 2020 | 27 views


Yes, that never fixes the problem. This explains why, and why you can't diagnose television problems on an online forum. The television sections are really only for help with manuals and remote codes.

Here are similar questions that we see often.
Question:

I've replaced everything in my television because it previously had a black screen with no lighting. Now it doesn't turn on at all and all I have is audio. What could be the cause ? Or

Turns on and sound works fine, but the picture is distorted (solarized? polarized? not sure what the term is) I replaced the main board, but that didn't fix it.
Or

I have an LG 55LM6200-UE with a dim lower-left. I just replaced both LED strips with no resolution. There is no physical obstruction visible, so this has to be a cable or board problem, right?

So your television stops working properly and you think it must be easy to fix, because you can buy boards on eBay, and you can watch YouTube videos. So you make a decision, you buy a board and you fit it, but the television still doesn't work as it should! This is a classic case of the 'let's try replacing this' method of television repair and illustrates why it is a bad idea. It doesn't work for a number of reasons. To correctly diagnose issues, you need to know every board, what it does and every component on the board. You need to know which part has failed, replace the component, or replace the board. The parts you purchased off eBay were probably out of scrapped sets and not tested. The part you put in was dead when you put it in, so you just moved on to another guess at what might be the cause and replace a board that is fine. And so it goes on, you change all the boards and it still doesn't work. Did you notice the large print that says 'NO Refunds, NO Returns'. This is to stop you sending your old one back and saying it didn't work, but the unscrupulous sellers use it as an excuse to get money for selling items that may, or may not work! The course to be a television engineer is 2 years full time education, take it to someone that knows how to diagnose and fix. It is by far the cheapest option. The part that failed might be a 20 cents fuse diode hard soldered to a board. They will charge you $5 in parts and a couple of hours labour. It's not the fix you want to hear, but it is the best advice.

Andrew - Fixya Moderator

Locks &... | Answered on May 15, 2020 | 42 views


Open it up.
Remove the battery.
Leave it for 15 minutes.
Install a NEW battery, yours is nearly depleted.

The battery doesn't have enough power to take your programming demands..

I fixed all the errors in your written question :>)

Locks &... | Answered on May 13, 2020 | 46 views


buy new one dude





DAFTAR ID PRO
http://dewapokerqqpkv.club

Locks &... | Answered on Apr 26, 2020 | 50 views


ASK GOGLE

Locks &... | Answered on Apr 22, 2020 | 63 views

Not finding what you are looking for?
Brinks 102-44831 Solid Steel Shrouded Padlock, 1-13/16-inch Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Brinks Locks & Locksmithing Experts

john h

Level 3 Expert

23424 Answers

Brad Brown

Level 3 Expert

18397 Answers

Are you a Brinks Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...