20 Most Recent Saniflo Saniplus Macerating Pump - Page 3 Questions & Answers

replace the worn seals or parts inside it

Plumbing | Answered on Dec 01, 2020

What information do you require ... try google.

Plumbing | Answered on Nov 21, 2020

I too have a Belanger tub and shower set and the taps have no screws under the caps or hex keys around the sides for removal.

Plumbing | Answered on Nov 01, 2020

Visit Lowes or Northern Tools stores to ask for assistance.

Plumbing | Answered on Sep 09, 2020

It's located under the RV carriage, positioned next to the gray tank which holds the water run-off from sinks and showers. The black tank should only contain the biodegradable enzymatic product of your choice, your solid and liquid waste, and septic safe toilet paper - nothing else. Also, don't forget to clean it! Create a plan, pay attention, wear gloves, and don't get distracted. Gross things happen when we're not focused on what we're doing; the black tank fiasco scene from the movie RV with Robin Williams comes to mind. Create a plan, pay attention, wear gloves, and don't get distracted. Gross things happen when we're not focused on what we're doing; the black tank fiasco scene from the movie RV with Robin Williams comes to mind. Attach the sewer hose securely to the tank valve after removing the valve cover. Then place the clear elbow into the sewer hole. Some may screw in; some may have a rock for you to place on top of your connector. This is advisable as you don't want that line getting dislodged. Also, after a year of exploitation, I had to replace globe valve, but I hope you will not face such a problem. I read several articles and realized that this is a very rare case when it fails.

Plumbing | Answered on Aug 17, 2020

The pressure produced by a pump depends on it's capacity and efficiency, the power of the motor driving the pump and the resistance of the pipework.
Without the resistance provided by the usual pipework the pump produces negligible pressure and just merely moves the liquid.

Given the motor power and pump capacity/efficiency are fixed values, the only reason the pressure would increase is the resistance provided by the pipework has increased.

Plumbing | Answered on Jul 30, 2020

If it isn't too late, I have a single crystal knob also. Couldn't find another when one of mine broke, so I bought two in the chrome finish. Let me know if you're interested in my (unbroken!) crystal knob.

Plumbing | Answered on Jun 30, 2020

  1. Step 1: TURN OFF WATER.
  2. Step 2: PRY OFF HANDLE.
  6. Step 6: REMOVE THE O-RING.

Plumbing | Answered on Jun 17, 2020

I doubt the kitchen tap is actually turning itself on - or is it?
Perhaps fluctuations in water pressure are defeating the tap...

More details would have been helpful, such as mentioning the tap design (traditional or quarter turn type?) and when the hammering noise happens?

Hammering is often caused by a worn tap. When turned partly on the jumper can vibrate and cause the pressure in the pipe to fluctuate and magnify the noise, especially when there is a long run of pipe that is inadequately clipped to the wall...

Plumbing | Answered on Jun 06, 2020

How to Remove the Sprayer on a Moen 7900 Faucet
  1. Turn off the valves under the sink by rotating the valve handles counterclockwise.
  2. Hold the hose in one hand and push upward on the hydrolock connection with the other to disconnect the sprayer from the diverter. ...
  3. Pull the sprayer straight upward and out of the guide.

Plumbing | Answered on May 19, 2020

The LED indicator light on the base of the faucet will start blinking red when it is time to change the batteries. If the batteries are not replaced in time, the faucet will still function with manual operation. ... Place the battery pack as close to the floor of the cabinet as possible.



Plumbing | Answered on May 09, 2020

Possible remedies are: allowing the water to run for several days (in the case of a new well), screen installation or replacement (for a sand and gravel well), or installing a liner in a sandstone well.
Six coman cause:

Plumbing | Answered on May 09, 2020

Submersible pumps usually use #10 non-detergent oil.

Plumbing | Answered on May 07, 2020

This is a shot in the dark... Hose connectors that push into a fitting do have a release mechanism. Usually this is a small fitting that pushes into the collet releasing the hose. Following the hose to the collet, the release should be the first thing you come to. Try pushing this into the collet and tugging on the hose.

Plumbing | Answered on Apr 29, 2020

If it is an older water line you could have corrosion built up in the lines coming up to the tap. causing the dribble.

Plumbing | Answered on Apr 19, 2020

You did not post the manufacturers name. Therefore It is hard to say what type of float switch is in it. It is not possible to get all the water out with a system like you are probably talking about. You can adjust a tethered float by changing the length of the tether. That is all I can say without knowing more about the system.

Plumbing | Answered on Apr 19, 2020

Not finding what you are looking for?
Saniflo Saniplus Macerating Pump Logo

2 questions posted

Ask a Question

Usually answered in minutes!

Top Saniflo Plumbing Experts

Bill Johnson

Level 2 Expert

306 Answers

Vernon Taylor

Level 3 Expert

7417 Answers

Tom Chichester

Level 3 Expert

61088 Answers

Are you a Saniflo Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Saniflo Plumbing

  • Saniflo Plumbing

Most Popular Question

get lid over rubber older saniplus seal

  • Plumbing