Top 20 Bushnell Tour V2 Pinseeker Laser Rangefinder Questions & Answers

Mine showed the same, found to be the mode button stuck in, removed button and used cotton bud with alcohol rub into the rubber seal, gave it a good clean and now as good as new. Hope this helps.

My tablet got wet. I put it away in my room and forgot it for 3-4 weeks. When I found it and tried it - voila! It worked perfectly. May be thats a solution.

If the jolt (vibration) doesn't work on your Bushnell V3, follow the instruction steps to change the unit of measure. (On the initial screen, hold down the "POWER/FIRE button, and it will cycle through your choices.) It flashes 3 times on each option. The first option is "Yards w/JOLT" even though the choice is abbreviated on the screen. Per the instructions, by releasing the POWER/FIRE button, you select your option. Wait until the 2nd flash on this choice to release the POWER/FIRE button, and the JOLT feature will be turned back on. (On mine, it didn't work by letting go on the first flash.)

Just replace the battery

I have a Bushnell Tour V2 that has worked very well for over 8 years and it just started doing the same thing with the frozen screen and 1888 yards. Since I just replaced the battery that I bought at a Pro Shop about 6 months ago I thought the battery was fine. I looked at the battery and did not recognize the brand so I went out and bought a new Copper Top Duracell and BANG it is working again just like new.

If you are seeing the circle through the view finder when pressing top button ( so battery is OK ) but nothing happens when you press the button on top a second time to operate the laser it may be the same problem I experienced .... I noticed a slight rattling from inside my V2 when I shook it . As it was around 8 years old and a bit battered I striped it down , peel off top and bottom rubber bits then the front rubber cover , this exposes small screws which can be removed easily with the correct screwdriver , once all removed the plastic covers can be separated ...do it carefully and remember which way it all fits back ! It's not that technical but a bit fiddly , I noticed that a small mirror ( prism ) about 1cm long had fallen from its location and was rattling around , I relocated it and added a tiny amount of glue to its edge fixing it in place , I made sure the glass was clean with no fingerprints on it...reassembled and worked fine .... you will need some glue to refix rubber bits , good luck .

Follow the instructions on page 8 of this manual: http://www.bushnellgolf.com/downloads/201930%20201933%20201940%206LIM.pdf

Had the same problem with my first Bushnell V2 (Slope). Worked intermittently and sometimes just quit altogether. Finally had to send it back to them. They sent it back and said nothing was wrong with it. I called them and told them they were wrong and I was sending it back and they should take more time in testing it. This time they acknowledged problem, said it was fixed and sent it back to me. I wound up getting a real good deal on the V2 without the slope calculator (necessary if you want to use it in championships). Used this one for some time with no problem, but now it just went dead again. Battery tests well into green area on meter, but I'm going to try a brand new one and see what happens. From all the things I've read about the V2 and battery life, it looks like you might need pretty fresh batteries to keep it going.

Hi I think the answer is simple, NO you have NOT received the right cap, you are indeed correct, in what you think & say.
I think you need to contact Bushnell, direct, via the Phone, and speak to someone in parts and explain what's happened, and explain what your cap is like, i am sure then they will sort it all out for you, and may even give you a refund for the one that will not fit correctly.
link below use the Contact link and find the Phone or if they have it Chat link, and contact them direct.
http://www.bushnell.com/global/customer-service/parts-information/

Hi mcallen173,

If you find that the screw settings are similar when compared to the previous cap then it is the same cap , however what you need to do is find out the right of the screws will fit the cap.

If the screw slots are not matching perfectly then it's not the cap that is required for your camera.

Many a times manufacturers assume that a particular cap of a different model will fit in some other model , which in actuality is not true , therefore you need to have the exact model of the cap.

You should notify this to the manufacturer and should get the new cap as it is , a good idea would be to send a snap of the are where you would fit the cap to them so that it makes them understand the right type of cap that is required.

Hope this helps ...:) Let me know in case you have any queries.

The e31 error apparently has to do with not using alkaline batteries try replacing the batteries with regular alkaline batteries and trying again.

Can you check that the new battery is an alkaline battery? If it is, and you are still getting the E31 error code, you will need to return your rangefinder to Bushnell to have it reprogrammed.

E31 is a programming error code. Most of the time this comes from using non-alkaline batteries or from letting a battery die in the unit. Non-alkaline batteries just don't generate enough current for the laser to operate properly.

Good luck.

Hi,

The Bushnell Tour V2 is notorious for suddenly stopping operating. Normally, if I slap the sides it starts working again. This has happened many times. I have checked the batteries and they are great. Try slapping.

If it does not help, Send an Email to below ID to contact Bushnell Email support with issue description and model # :

[email protected]


Regards,
Ron


* Please rate this solution with Thumbs up and Testimony to help us improve providing support

You will have to refer to your manual for the error code, and if it doesn't have it, you will have to contact Bushnell support:
http://www.bushnell.com/products/gps/product-support/support-steps/
You should first try cleaning the battery contacts inside the unit. Use a qtip and alcohol, or a pencil eraser. If this doesn't help, contact Bushnell.
Good luck,and hope this helps.

The Bushnell Tour V2 is notorious for suddenly stopping operating. Normally, if I slap the sides it starts working again. This has happened many times. However, two days ago it quit working again and I have slapped the **** out of it and it still doesn't work. I have checked the batteries and they are great. Try slapping. If someone out there knows something else that will help me, please let me know.

bill

The Bushnell Tour V2 is notorious for suddenly stopping operating. Normally, if I slap the sides it starts working again. This has happened many times. However, two days ago it quit working again and I have slapped the heck out of it and it still doesn't work. I have checked the batteries and they are great. Try slapping. If someone out there knows something else that will help me, please let me know. Slapping no longer helps in my case.

bill

no, this seems to be a hardware problem, check up with service centre.

Hi,
Authorized service center list you will only get at bushnell website. So visit to the given link and select "Customer Service" or you can contact them ans ask them to send you the nearest customer service center located at your place..... Or else you can inquire about the service station (authorized or local) to a dealer located at your place. They will be able to provide you other options too, if any.
http://www.bushnell.com/
Hope this has helped you... Thanks...

Hi,
Battery is not supplying the voltage required for the camera to work the range of voltage should be 2.9 to 3.2 volts . Since you have replaced new one there is some battery drain problem .
For sending to repair you can contact
8500 Marshall Drive
Lenexa, KS 66214
Contact number
(913) 752-3400
(800) 423-3537

Hope this helps .

for this you will need to send the unit into their repair at 8500 marshall drive lenexa ks 66214 4-6 week turnaround and put your name address and telephone number inside the package. if there is a cost they will send an estimate.