Behringer (UCG102) Sound Card - Answered Questions & Fixed issues
I need a 64 bits driver for Vista.
Here is the link to their support page, but they do not list 64bit versions for Vista, just the 32bit. Try contacting them to see if they are going to issue one.
http://www.behringer.com/EN/Products/UCG102.aspx
12/12/2014 9:36:19 PM •
Behringer...
•
Answered
on Dec 12, 2014
•
561 views
After installing the drivers I
if you are having trouble with your drivers
here is a general look at the drivers and how to update them
if your computer came with a motherboard disc the drivers could be on it
click start control panel administrive tools ,computer management ,device manager look through all of your devices if you see a yellow question mark?or exclamation mark ! or red x
right click to reinstall drivers or
if you can see your usb but its not workingports(com&lpt)right click update driver hope this helps
5/25/2011 11:39:39 PM •
Behringer...
•
Answered
on May 25, 2011
•
581 views
Sound doesnt come out from guitar link UCG102
what you need to do is install the asio4all driver then select file, adio midi settings and where it says behringer audio codec click the arrow and select asio4all then click the configure button and in the wdm list you must activate all the items under audio codec and the audio speaker under High Definition audio device this will allow it to work through the speakers, or just leave it how it is and plug in a set of headphones. make note though that your speakers will play nothing else but the guitar sound. all other music internet sounds, the lot will no longer work as your ucg102 is high jacking your sound card to produce the sound from your guitar. hope this helps.
1/28/2010 9:04:50 PM •
Behringer...
•
Answered
on Jan 28, 2010
•
6,346 views
Guitar Link UCG-102 no sound
What you have to do is go into your speaker program or just right click the little speaker at the bottom of your screen and go to playback options and disable the headphone interface that comes with the Guitar Link,
after this happens it will put it back to your default speakers
then click on the tab that says Recording options and turn up the volume on what should say Microphone USB Audio Codec
Afterwards go into your AC Box Combo program... hit "File" and than Audio+Midi Settings and At the top it should say "Interface" click on the box to the right of it and put it to your speaker program
Its decently complicated but it works
PEACE
3/26/2009 5:05:35 PM •
Behringer...
•
Answered
on Mar 26, 2009
•
8,365 views
Behringer Europower Pmp1280s, remove front panel
To remove the front panel of the Behringer Europower PMP1280S, you may need to follow these steps:
1. Ensure the device is powered off and disconnected from any power source.
2. Locate all the screws that secure the front panel to the chassis. Based on your description, it seems you have already removed the screws on the front side and the ones on the frame.
3. Sometimes, there may be additional screws hidden beneath labels or rubber feet. Carefully inspect the front panel for any hidden screws and remove them if present.
4. Once all the screws are removed, gently try to pull the front panel away from the chassis. It might be snug due to connectors or clips holding it in place.
5. If the panel still appears to be stuck in the middle, double-check for any screws that may have been missed or hidden. Make sure you have removed all the necessary screws to fully release the front panel.
6. If the front panel remains stuck, do not force it as it could potentially damage the device. Instead, consider consulting the user manual or contacting Behringer customer support for specific instructions or further assistance.
Remember to exercise caution when working with electronic equipment and always refer to the manufacturer's instructions or seek professional assistance if you are unsure.
6/20/2023 7:09:13 PM •
Behringer...
•
Answered
on Jun 20, 2023
•
71 views
Our new Behringer 2000 has stopped working. The green light doesn't come on when sound goes in microphone.
the green light is power indicator not mic level. the green light should come on when powered up. remove mike cable and the see if green light comes on, If it does power down and connect mike and cable (hopefully you have a good quality one and not a toy)
Call Behringercustomer service. Where did you buy it from, if new it is under warranty and need to replaced with another new one. It is not an audio mixer the yellow and right lights are for clipping.
6/9/2022 2:46:07 PM •
Behringer...
•
Answered
on Jun 09, 2022
•
81 views
How to connect a sound card behringer FCA 1616 firepower into a comptuter
Install all necessary audio drivers on your PC.
Connect the unit to AC power.
Connect the unit to your pc via either USB 2.0 or firewire serial bus.
Press and hold the DIGITAL SELECT button while powering the unit on to switch the bus mode from firewire to usb and vice versa.
10/20/2015 7:01:22 AM •
Behringer...
•
Answered
on Oct 20, 2015
•
513 views
B300 parts list
Have you tried going up on Behringers web site? You can google the part number.
5/7/2014 4:17:55 AM •
Behringer...
•
Answered
on May 07, 2014
•
367 views
Not finding what you are looking for?