20 Most Recent Dynex 5-in-1 USB 2.0 Mini Memory Card Reader - Page 4 Questions & Answers

Not to be a wise guy, but did you have the memory card in it when you connected up? If so, take it out and clean the contacts with a soft cloth and at least 90% alcohol. Also, look inside the reader to make sure none of the 4 pins are bent or broken. If all this fails, try it on another usb port. Sometimes they get reassigned by software or something, and won't detect certain devices on certain ports, for unknown (to me) reasons. If all this fails, try the card reader on another computer (maybe you should try this first). If everything fails, I would deduce the card reader is bad, and get another one. Good luck.

Make sure that the memory card is properly seated inside the card reader.
Try different cable.
Verify with the manufacturer, if this card reader is a Plug-n-Play or if you need to install a driver to the computer.

Try connecting it to different computer. Or try different types of memory cards (the cards should be supported).

If same problem occur, you need to contact the reseller, because the card reader could be defective.

Good luck!

If its a simple memory card reader, all you need to do is plug it into an available USB port then ensure your PC detects it. Also, make sure drive letters appear for each card slot. If you need further help, reach me via phone at https://www.6ya.com/expert/brandon_bf4b4a06876c89a0

you could put the mini-cd into another computer and put all the files on another cd or a flash drive then transfer to the macbook.

here is the link for your drivers.
hope this helps you.


http://www.dynexproducts.com/pc-580-2-dynex-5-in-1-usb-20-mini-memory-card-reader.aspx

Good Luck.

Happy Computing.

HAVE YOU INSTALLED THE SOFTWARE FOR YOUR DOWNLOADER ON YOUR 2ND COMPUTER?

JE NE PEU PAS UTILISER MON FLASH

Hello,

First of all make sure that the USB port that you are using to connect it to your PC is a USB 2.0 port, and not USB 1.0.

Also if it came with an external power, connect it to the external power before putting on your PC.

This is because the voltage supplied by USB 1.0 is lower than that of USB 2.0 and therefore might not be enough to power up your USB Drive.

After making sure about this, power up your system, and plug the card reader, then Right-Click on my computer icon, select manage, then go to Disk Management Option.

On the Disk management option Page you should see ALL the drives installed on your system, including the hidden ones, so what you will just do is, try and locate the one representing your memory card, and right click on it. then select "Change Drive letter and Paths", and give the drive any new, unique letter (i.e alphabet) different from the ones already on your system, and click on OK.

This should make your memory card to be detected automatically.

Hope this helps you out.

Goodluck!

Hi.

The unit listed is an external USB card reader. This unit does not require drivers to work on Windows Vista and Windows XP.

If your old computer has XP or Vista, and the Dynex drive works on the new computer, then there is a software problem on your old computer operative system.

In that case try disconnecting computer from power , and if the computer is a laptop also removing battery at same time. Leave computer disconnected for two minutes to drain power.

If that does not work, or if you have a system older than Windows XP, or if you have a Mac, you can try downloading drivers from Dynex link here.

Regards.

Windows should automatically install the required drivers. Just plug and play.

Confirmed by Dynex Product Website

Check that your card type is compatible with the sockets.

When a card fits, it goes in with the metal contact strips face down, at the front. They normally require hardly any pressure to go in.

Sometimes my computer won't recognize my memory cards but here is a trick. Put your memory card in your card reader before you start up your PC. When you start up your computer it will scan all of its hardware along with the memory card.
i hope these can help

Does your Dynex have a minisd card reader? if it does not have a minisd card reader, you need a SD adapter that turns the minisd into a SD card.

The microSD and miniSD are different in shape and in the amount of pins on the card.

you will need a proper adater or a proper slot.

Can you send me the brand and model of your reader so I can tell you if you need a adapter for the card or if you should be able to read it.

But it seems to me that you need the adapter.
Here is a adapter for miniSD - to normal SD
http://www.newegg.com/Product/Product.aspx?Item=N82E16812189064&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Adapters+and+gender+changers-_-Link+Depot+Corp.-_-12189064

the price of the adapter is $2.29

got a fujifilm xd card reader the icon is there on my computer everytime i click on it it tells me to insert disc

Try rebooting and see if it shows up properly. If it doesn't, there could be a conflict with driver letters.

Right-click My Computer and choose Manage
Left-click Disk Management
See if your device is listed there. If it is try assigning it a new Drive Letter Right-click and choose Change Driver Letter and Paths.
Click Change.
Choose a new drive letter, problem something lower than E.
Click OK.

Unplug and reattach your device and see if it will work properly.

You can download the drivers from the Dynex website.
External USB 2.0 Multiformat Memory Card Reader Drivers

Try it after format. may be its files system is different from Windows...

Try downloading the driver from manufecturer's website and install the drivers.

According to what I was able to find the device does not require to be opened to insert the storage media.

I am assuming the device you are referring to is the same as the device shown in this link: http://www.dynexproducts.com/pc-314-2-dynex-5-in-1-usb-20-card-reader.aspx

If you are having troubles getting your storage media to fit into the slot then it is possible that the media type is unsupported by the device or that the storage media is being inserted incorrectly.


I hope this solves your problem, best of luck.