20 Most Recent
Insignia Digital-to-Analog Converter for Analog TVs - Page 5 Questions & Answers
I've connected the red, yellow and white plugs to
Hi where you plugged the rca cables into on the tv it will tell you what input it is. You must select that with the input button on the tv or remote.For example if it says vid1 you select vid1 whit the input button also make sure the yellow rca is plugged into yellow on the tv this is the video wire.
2/1/2010 2:19:53 AM •
Insignia...
•
Answered
on Feb 01, 2010
Need to hook up dvd/vcr combo with converter box
Connect your rabbit ears to the Insignia. Connect the Insignia to the antenna input on the "cvd/vcr combo". Now turn on the television to show the "cvd/vcr combo".
The Insignia simply goes between your antenna and your television. In your case you also have a vcr so if you want the VCR to be able to play and record digital stations you will need the Insignia between the vcr and the antenna.
12/29/2009 2:46:05 AM •
Insignia...
•
Answered
on Dec 29, 2009
I cannot turn off the TV,with the insignia remote control
Read the first time start up instructions .. This is what worked for me.
Hold the power-on/off button down while simultaneously pressing channel up , repeatedly for up to 45 times. when the TV shuts off stop, release the on off button.
you should be able to turn it on and off, if you went too far (pressed up arrow too many times), go the other way (holding down the on off and pressing channed down) until it turns on again.
12/22/2009 10:12:19 AM •
Insignia...
•
Answered
on Dec 22, 2009
How to connect my dvd & vcr with the converter box
Here is my setup.
1) Separate DVD player
2) Separate VCR
3) Digital to Analog Converter box
4) Analog TV
5) Rabbit ears (UHF/VHF) antenna
The antenna goes into the converter box.
The RF-output of the converter goes into the RF-Input of the VCR
The DVD output goes into the front input jacks of the VCR
The VCR RF-output goes into the TV RF-Input
The VCR Line output goes into the front of the TV
To watch DVDs, we turn on the DVD player, turn on the VCR, and set the VCR channel to L2, and tune the TV to channel 3. The converter is off.
To auto record on the VCR, the converter must be tuned to the station being recorded. The converted must be turned on, the TV can be off.
To watch VCR tapes, turn the TV and VCR on. The TV is set to channel 3. Just press play on the VCR.
To Watch TV. Turn the TV and converter on. The TV is set to channel 3. Change the stations using the converter.
12/19/2009 8:43:07 PM •
Insignia...
•
Answered
on Dec 19, 2009
My upstairs tv had been
Hi and welcome to FixYa,
Initially, please postback with the model numbers of the Quasar TV and / or the Quasar remote control.
Offhand, to try are:
- press 0, then 3 on the remote; or
- press 0, then 3, then ENTER or OK on the remote; or
- perform scanning or channel setup (Add).
Good luck and thank you for asking FixYa.
12/5/2009 7:25:00 AM •
Insignia...
•
Answered
on Dec 05, 2009
I have hooked up my converter box but its not
make sure u have the antena hooked to box and box hooked to tv, make sure antena wire is actually hooked to an antena if wire is coming out of the wall, otherwise u more than likely need a new antena, or box it's self is bad but if it turns on and u see somtin on the screen like make sure antena is hooked up then the box is probaly good
11/27/2009 10:37:24 AM •
Insignia...
•
Answered
on Nov 27, 2009
Cant turn off tv
u probaly need to set the remote to tv, then put in the tv code. NOTE most if not every im not 100% sure but most convrters remotes only control just the power and or the volume on tv's
11/27/2009 10:20:29 AM •
Insignia...
•
Answered
on Nov 27, 2009
I can no longer get nbc on my converter box
try doing a rescan of the channels, might also be new RF signal obstruction in the area, try re pointing your antenna a different angle, this helped me once when a weak channel was freezing often.
11/18/2009 4:23:08 AM •
Insignia...
•
Answered
on Nov 18, 2009
Not finding what you are looking for?