20 Most Recent Hotpoint 30" Self-Cleaning Freestanding Gas Range - Black Questions & Answers

Gas ovens are fitted with at least one safety device and it could be it has failed.

The safety device is bypassed while the pilot light is lit. The pilot light heats a thermocouple bulb which switches the gas on to the burner. As long as the pilot light continues to heat the bulb gas will continue to flow - until the thermocouple fails, they aren't long-lasting...

Hotpoint 30"... | Answered on Feb 03, 2018

What is the complete model number of your unit?

Hotpoint 30"... | Answered on Dec 15, 2012

continued igniton when gas is off faulty igniter switch sticking on

Hotpoint 30"... | Answered on Aug 02, 2012

Here you are. :)12_27_2011_3_08_30_am.jpg

Hotpoint 30"... | Answered on Dec 27, 2011

You should be able to find a manual on the Internet. ~Denise

Hotpoint 30"... | Answered on Jul 04, 2011

That noise is likely the thermal fuse in the back. It can be replaced. If you are not getting any power to the control panel or the rest of the oven, this is likely the cause.

Hotpoint 30"... | Answered on Aug 31, 2010

the model number should be ...open oven door look in the upper left or right hand corner or pull oven top up look in may be data plate their

Hotpoint 30"... | Answered on Aug 22, 2010

There are several possibilities here, could be thermal fuse, failed transformer, failed control board. If you post the full model number we may be able to look up the wiring diagram and see which looks most likely. The thermal fuse is a relatively inexpensive repair. If it turns out to be the transformer or control board we repair these at www.fixyourboard.com which can save you some dollars.

Best Regards,

Hotpoint 30"... | Answered on Jun 21, 2010

The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating

Oven Problems Replacing the Igniter http://www.fixya.com/support/r4572625-oven_problems_replacing_igniter


Hotpoint 30"... | Answered on May 15, 2010

This tends to be the problem due to power surge which has been caused by the lightening .The circuit breaker might have been damaged also chance that the fuse inside kitchen range is blown . If fuse is bad then ignition won't work properly .You need to replace with new one .

Hope this helps .

Hotpoint 30"... | Answered on May 04, 2010

The first thing to check is the wiring and make sure it is all secured and connected properly.
Then check the bake element and use an ohm meter to check for continuity,if there is no continuity the replace the element.
if those items are good then you will need to replace the electronic control boardor commonly called the clock timer.

Hotpoint 30"... | Answered on Mar 03, 2010

you first need to check that proper voltage is coming in. if it's electric then it's 240v. if that's fine, the control board might be defected.

Hotpoint 30"... | Answered on Jul 07, 2009

sounds like electronic ignition is worn out

Hotpoint 30"... | Answered on May 27, 2009

Not finding what you are looking for?
Hotpoint 30" Self-Cleaning Freestanding Gas Range - Black Logo

27 questions posted

Ask a Question

Usually answered in minutes!

Top Hotpoint Kitchen Ranges Experts

Cindy Wells

Level 3 Expert

6166 Answers

Fahr Quad

Level 3 Expert

774 Answers

Ned Halaweh
Ned Halaweh

Level 2 Expert

240 Answers

Are you a Hotpoint Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hotpoint Kitchen Ranges

  • Hotpoint Kitchen Ranges

Most Popular Question

oven not heating broiler burners work

  • Kitchen Ranges