20 Most Recent Premier 24" Freestanding Electric Range - Biscuit - Page 5 Questions & Answers

To clean stains on the Russell Hobbs 2 Plate Mini, you can follow these steps:

1. Turn off and unplug the mini stove to ensure your safety.
2. Allow the plates to cool down completely before cleaning.
3. Make a solution of equal parts of white vinegar and water in a spray bottle.
4. Spray the stained areas with the vinegar and water solution.
5. Let the solution sit for a few minutes to break down the stain.
6. Wipe the plates with a soft cloth or sponge, applying gentle pressure.
7. For stubborn stains, sprinkle baking soda on the plates and scrub gently with a sponge or brush.
8. Wipe the plates clean with a damp cloth and let them air dry completely before using the mini stove again.

Note: Avoid using abrasive cleaners or scrubbers as they may scratch the surface of the plates. Also, avoid using harsh chemicals that may damage the surface or the heating elements of the mini stove.

The Westinghouse has no power sockets on the side of the cooker!

Not very good at reading wiring diagrams, but hopefully someone else on Fixya can assist you. Here's a site I found hopefully someone can chime in. Best to you https://www.buyspares.com/kenwood/cooker-oven/ck408-c9t0kw018x/catalogue.pl?path=441691%2C261565&model_ref=2588765&illustration_ref=2313971

Hi, you've taken the correct steps to start. Please attempt to slide some parts of the magic chef to the side. Also, look on the bottom of the device. If all else fails, please call magic chef to find out where the cord might be plugged in. Thank you.

Can you please send me the wire diagram by color to connect to wire board panel like red, grey white etc. for gas stove JGBP28BEJ1CT gas stove I bought a replacement but forgot to take a picture

Question edited for a lot more clarity. So few words, so many mistakes and yourspacebarisbroken! Please proof read before you post! Probably needs a new glow plug. https://www.google.com/search?q=efel+oil+stove+won%27t+light+up

To replace the broken light on your Broan Allure range hood, you will need to follow these steps:

1. Turn off the power to the range hood by unplugging it or turning off the circuit breaker.
2. Remove the filters by gently pulling them down and then out of the range hood.
3. Locate the light cover and remove it by pulling it towards you.
4. Use a screwdriver to remove the screws that are holding the light assembly in place.
5. Carefully pull the light assembly out of the range hood.
6. Replace the broken light bulb and ensure that it is securely in place.
7. Reinsert the light assembly into the range hood and tighten the screws.
8. Reattach the light cover by pushing it back into place.
9. Replace the filters by pushing them back up into the range hood.
10. Turn on the power to the range hood and test the new light to ensure it is working properly.

Note: If the light assembly is wobbly, you may need to tighten the screws that hold it in place or replace any damaged parts.

Contact some technicians in your local area directly. That will be the easiest way to get prices.

There are a few other things you can try to troubleshoot this issue:

1. Check the oven gasket: If the gasket around the oven door is worn or damaged, it could be letting heat escape from the oven, which can prevent it from reaching the desired temperature.
2. Check the oven igniter: If the oven igniter is faulty, it may not be able to draw enough current to ignite the gas and heat the oven. You can test the igniter with a multimeter to see if it is working properly.
3. Check the oven thermostat: The thermostat regulates the temperature inside the oven. If it is faulty, it may not be able to maintain the desired temperature. You can test the thermostat with a multimeter to see if it is working properly.
4. Check the control board: The control board regulates the oven's heating elements and can be a source of problems if it is faulty. You can test the control board with a multimeter to see if it is working properly.

If none of these solutions work, it may be best to call a professional technician to diagnose and fix the problem.

If your Pit Boss 820 pellet grill is not maintaining the set temperature and continues to climb, there could be a few potential causes.

1. Damaged temperature probe: The temperature probe is responsible for sending the temperature readings to the controller. If it's damaged or malfunctioning, the controller may not be able to regulate the temperature properly.
2. Faulty controller: If the temperature probe is working correctly, the controller could be the problem. If the controller is faulty, it may not be able to read the temperature correctly and regulate the temperature properly.
3. Airflow obstruction: Another possible cause is an obstruction in the airflow. If the airflow is restricted, it can cause the grill to overheat.

To troubleshoot this issue, start by checking the temperature probe and controller for any visible damage or signs of malfunction. If they appear to be functioning correctly, check for any obstructions in the airflow. If the issue persists, it's recommended to contact the manufacturer or a qualified technician for further assistance.

If all the lights on your pellet stove are on when you plug it in, it could be a sign of a malfunctioning control board. The control board is responsible for regulating the stove's functions, and if it is damaged or malfunctioning, it can cause the stove to behave erratically. You can try resetting the stove by unplugging it from the power source for a few minutes and plugging it back in. If this does not work, you may need to contact a professional technician to diagnose and repair the issue with the control board.

If you have cleaned the igniters on your Elve stove top and turned off the power, but they still keep clicking, there may be a few potential causes:

1. Wetness or moisture: If any of the ignition switches, spark module, or wiring harness has gotten wet or damp, it can cause the clicking sound to continue. Try drying off the stove top and allowing it to sit for a few hours before trying again.
2. Loose wiring: Check the wiring connections on the spark module and ignition switches to ensure they are tight and secure. Loose wiring can cause a short circuit and result in the clicking sound.
3. Dirty burners: Even if the igniters are clean, the burners themselves may be dirty or clogged, preventing gas from flowing properly. This can cause the igniters to continue clicking in an attempt to ignite the gas. Try cleaning the burners thoroughly and see if that resolves the issue.
4. Defective parts: If none of the above solutions work, there may be a problem with the spark module, ignition switches, or wiring harness. In this case, it may be best to contact a professional technician to diagnose and fix the issue.

Replacing a surface burner igniter on a Jen-Air Gas Convection Range JGRP536 can be done by following these steps:

1. Turn off the gas supply to the range.
2. Lift up the cooktop and locate the igniter that needs to be replaced.
3. Remove the screws that secure the igniter bracket to the burner assembly.
4. Carefully lift the igniter bracket off the burner assembly and disconnect the wires from the igniter.
5. Remove the old igniter from the bracket and discard it.
6. Install the new igniter onto the bracket and connect the wires to the new igniter.
7. Reinstall the igniter bracket onto the burner assembly and secure it with the screws.
8. Lower the cooktop back into place.
9. Turn the gas supply back on and test the new igniter to make sure it is functioning properly.

Note: It is important to make sure the replacement igniter matches the specifications of the original igniter for proper function and safety. If you are not comfortable with performing this task, it is recommended to seek the assistance of a qualified technician.

If your oven temperature keeps dropping and takes too long to heat back up, it could indicate a problem with your oven's heating system. Here are a few things you can check:

1. Check the oven's heating elements: If one of the heating elements in your oven is faulty, it may cause the oven temperature to drop. Turn off the oven, unplug it, and visually inspect the heating elements. If you see any signs of damage, such as cracks or breaks, the element may need to be replaced.
2. Check the oven's thermostat: A faulty thermostat can also cause your oven to drop in temperature. You can use an oven thermometer to test the accuracy of your oven's thermostat. Simply place the thermometer inside the oven, set the oven to a specific temperature, and wait for it to heat up. Check the thermometer to see if it matches the oven's temperature setting. If it doesn't, the thermostat may need to be replaced.
3. Check the oven's door seal: A damaged or worn door seal can cause heat to escape from the oven, which can result in a drop in temperature. Inspect the door seal for any cracks, breaks, or other damage. If you notice any issues, replace the seal.
4. Check the oven's control board: If the above steps do not resolve the issue, it could be a problem with the oven's control board. Consult a professional technician to diagnose and repair the issue.

Replacing a switch and circuit board on a Broan vent hood model 88,000-c requires some electrical knowledge and experience. If you are not comfortable working with electricity, it is recommended that you hire a licensed electrician to perform the replacement. Here are the general steps for replacing the switch and circuit board on your Broan vent hood:

1. Turn off the power to the vent hood. You can do this by turning off the circuit breaker or unplugging the vent hood.
2. Remove the cover of the vent hood. This usually involves removing screws or clips that hold the cover in place.
3. Locate the switch and circuit board. The switch and circuit board are typically located near the control panel on the vent hood.
4. Disconnect the wiring from the old switch and circuit board. Take note of which wires go where, so you can reconnect them to the new switch and circuit board.
5. Remove the old switch and circuit board from the vent hood.
6. Install the new switch and circuit board in the same location as the old ones.
7. Reconnect the wiring to the new switch and circuit board. Make sure to connect the wires to the correct terminals.
8. Replace the cover of the vent hood.
9. Turn the power back on to the vent hood and test the new switch and circuit board to ensure that they are working properly.

If you encounter any difficulties during the process, it is best to stop and seek assistance from a professional. Safety is a top priority when working with electrical systems, and it is important to take proper precautions to avoid injury or damage to your home.

If the motor of your CDA cooker hood has stopped working, but the lights are functioning properly, it could be due to a faulty motor or a problem with the motor capacitor. Another possible cause could be a broken wire or a loose connection in the motor circuit. It's recommended to have a professional inspect and repair the cooker hood to ensure safe and proper operation.

The Scentsy temp burner is not designed to be used on a stove. Scentsy warmers use a heating element to melt scented wax, not an open flame. Using the Scentsy temp burner on a stove or any other heat source with an open flame could be dangerous and is not recommended. If you're having trouble using your Scentsy warmer, I recommend consulting the manufacturer's instructions or contacting Scentsy customer support for assistance.