Denon AVR-1513 - Answered Questions & Fixed issues

My unit is not powering ON

Short circuited component/s inside the circuit board.

Denon AVR-1513 | Answered on Oct 25, 2015 | 162 views

Is there a general issue with video and sound cutting/jumping out with more volume applied?

Power supply section circuit problem. Check all the voltages and filter capacitors at this section. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Denon AVR-1513 | Answered on Jun 02, 2015 | 90 views

How do I unlock Denon AVR-1513 Remote

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Denon AVR-1513 | Answered on Aug 10, 2014 | 203 views

Volume coming from tv is so low

you have to goto setting and set the speaker to tv if you have a newer tv

Denon AVR-1513 | Answered on Mar 28, 2014 | 67 views

Blinking red light

How many times this power/standby light blinks? It is fault indication, and are fault codes. If you wish to get some details about these codes, try this link. http://electronicshelponline.blogspot.com

Denon AVR-1513 | Answered on Dec 23, 2013 | 150 views

No sound coming out of the speakers

set the speaker as default, whichever you are testing, it will start working, just right click and select.

Denon AVR-1513 | Answered on Dec 15, 2013 | 167 views

Stereo shuts off at 69

This could be due to the systems overload protection kicking in, which under normal circumstances shouldn't happen, I suggest moving the speakers next to the amplifier and if possible use anew piece of wire to test the speakers start with one and test each individually. I think you possibly have a small short in one of the wires. Or one speaker is damaged. Measure the resistance between each speaker wire pairs. The speaker will probably be either 4 or 8 ohms check that this is the case. Read the speaker labels for clues. Were they the original speakers supplied? by the same manufacturer?

Denon AVR-1513 | Answered on Dec 09, 2013 | 66 views

I got a LG ht33s subwoofer to my denon avr1513. Connected with RCA cable but no sound.

make sure the wattage of the amplifier has the same amount or more wattage to the subwoofer otherwise it will not be able to produce sound because of power complications

Denon AVR-1513 | Answered on Dec 07, 2013 | 87 views

Every time I turn power off or change input source

Check and replace its main system control memory IC.

Denon AVR-1513 | Answered on Aug 23, 2013 | 63 views

Avr 1513 no signal to subwoofer

Check its speaker connections. Check the speaker using a dry cell. If it is found OK, check the sound settings. If you wish to get more details, check this link.

Denon AVR-1513 | Answered on Mar 22, 2013 | 172 views

How to fix my Denon DBP-4010ud Blu-Ray Player

Appears to be a software problem. Unfortunately, some blu-ray players contain software that expires, requiring you to repurchase newer, more expensive software from the manufacturer in order to continue to play blu-ray discs. Check your software for the player. No freeware blu-ray software out there.

Denon Televison... | Answered on Nov 13, 2019 | 222 views

User manual for Denon remote rc-1030?

Contact Denon for assistance:

Chat link: https://denon.custhelp.com/app/chat/chat_launch

https://denon.custhelp.com/app/answers/detail/a_id/208/~/programming-a-device-to-my-avrs-remote

Denon Televison... | Answered on Jun 13, 2019 | 162 views

A DVD playing on my Denon 1805 froze. I usually can fast fwd past such problems, but ng. I replaced the disc and now it won't it load. I tried a 2nd DVD and it also won't load. What is my problem?

Verify that the disc turns, put it in the tray, observe the position, enter it, wait for the indication of "No Disc" and remove the disc, if it is in the same place, apparently, it would have problems in the disc engine
Another way to check if the engine works, play an audio CD, if you read it, apparently the engine, it would not be the cause of the failure
If I notice that I turn, I could have dirt problems in the lens of the reader, proceed to clean it with a cotton swab and if you do not know how to do it, contact a technical service
Another option, it is possible that your reader is under power to read the DVD

Verifique que el disco gire, p?ngalo en la bandeja, observe la posici?n, ingreselo, espere a la indicaci?n de "No Disc" y saque el disco, si esta en el mismo lugar, aparentemente , tendr?a problemas en el motor del disco
Otra forma de chequear si el motor funciona, reproduzca un CD de audio, si lo lee, aparentemente el motor, no seria el causante de la falla
Si observo que giro, podr?a tener problemas de suciedad en el lente del lector, proceda a limpiarlo con un hisopo de algod?n y si no sabe como hacerlo, dir?jase a un servicio t?cnico
Otra opci?n, es posible que su lector esta bajo de potencia para leer los DVD

Denon Televison... | Answered on Apr 14, 2019 | 33 views

When I opened my Denon remote, it was full of glue. It was also dead. Should I remove the glue ? before cleaning. AVR -1610 remote RC-1120.

How do I reset my Denon remote?
All the settings are restored to their defaults. Press and hold RC SETUP for more than 3 seconds. "SETUP" and indicator flashes twice on the remote control unit. Use to display "RESET" on the remote control unit and press ENTER

Denon Televison... | Answered on Mar 08, 2019 | 158 views

A denon AVR1505 and remote

If you have the Audyssey set up mic, plug it in and follow the on screen instructions. Or try installing the Denon AVR remote app.

Denon Televison... | Answered on Dec 26, 2018 | 57 views

Which remote control do i need for a denon udra 90

It is the Denon RC-170.

Denon Televison... | Answered on Nov 01, 2018 | 191 views

Denon avr 589 shuts off with no speakers connected and no volume

Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
https://homenol.blogspot.com/
https://electronicshelponline.blogspot.com/ Search the site by type in the "brand name" to your device, [Exclude the model number] in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Denon Televison... | Answered on Feb 17, 2018 | 282 views

Seeking how to program Denon RT-605 universal remote. I've had it for years but haven't used it for so long I don't remember how. Any help would be great, thanks.

Try go ogling it. Might get lucky

Denon Televison... | Answered on Jan 04, 2018 | 85 views

I have a 20.1 Dish remote controller. I would like to use the AUX selection to operate my Denon AV receiver. Can you help me with this?

Depending on the age of your receiver, this may be possible. Turn on the receiver. Then press and hold the Aux button until all of the mode buttons light up. Press 2 to tell the remote that the unit to be controlled is an audio receiver. Then you will need to try one of the Denon 3-digit codes. Press # and check that the mode flashes 3 times. Check if your receiver turns off. If it does, check if the other buttons work to control the receiver. Otherwise try another Denon code by starting at the press and hold the Aux button step.

If you want the remote only to control the volume, mute and power functions of the receiver, press 1 after entering the three-digit code and before pressing the # key.

The Denon device codes to try are 669 670 680 682 696
744 759 760 762 792 809 . You can find the directions for programming the Aux key on page 11-12 of the manual. The code list for audio devices starts on page 43. The manual is available from Dish here: https://www.mydish.com/filestream.ashx?ID=3025 . Usually the code list for universal remote features will not always work with devices that were released less than 6 months before the remote was programmed. Devices released after the remote was programmed are similarly not guaranteed to be supported.

I hope this helps.

Cindy Wells

Denon Televison... | Answered on Mar 29, 2017 | 208 views

Working on a Denon DVD-3910. Need to replace the DVD mechanism (FG180-1). I've found a few versions; FG180-1W, FG180-1-DE, FG180-1-DE-W. Will any work? are any better than others?

Yes call Denon.

Denon Televison... | Answered on Nov 22, 2016 | 167 views

Not finding what you are looking for?

Popular Tags

unlock remote

24 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Denon RC-8000 LCD Touchscreen Remote Control

18 Questions

Denon DVD-2910 DVD Player

18 Questions

Denon DVD-3910 DVD Player

14 Questions

Denon S-301

30 Questions

Denon DBP-4010 Blu-Ray Player

6 Questions

Check Out the Latest HD Televisions Report

View all Fixya Reports

Top Denon Televison & Video Experts

Muntejaya Ginting

Level 3 Expert

10422 Answers

The Knight

Level 3 Expert

76466 Answers

Grubhead

Level 3 Expert

5700 Answers

Are you a Denon Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for Denon AVR-1513? Or just drag it here!

Loading...