20 Most Recent Denon AVR-1513 - Page 7 Questions & Answers


disk reading failure you can try to clean the optical lens by wipeng it with a cotton buds moisten with an alcohol..check also the ribbon wire that connects between the lens and the mainboard make sure that the ribbon is intact with no broken lines and perfectly fits to the socket.re attached all the connectors from the board..good luck hope this helps you..

Denon Televison... | Answered on Feb 21, 2011


Try website like Remotes.com to buy an exact remote to the original remote.

Denon Televison... | Answered on Nov 15, 2010


Hi have you try to open the remote and clean it inside sheet rubber and pcboard use alcool and tooth brush then maked dry make shure theres no residu left on contact sheet and board..
hope that will hell you...

regards alan

Denon Televison... | Answered on Oct 21, 2010


Hi,

It seems that there has been an issue with IR sensor.In most of the cases, investing in new remote is a wise option. However, as you have already changed the batteries, few more simple steps you could follow :-

1. Try to use the remote from close.

2. Clean the battery connectors. Most of the times, you might find dirt and debris out there.

3. Dissemble the remote. Clean the sensor and the keypad and then reassemble it.

If you wish to repair it, i would be glad to help. However, as i said the cost of repair is usually more than investing in new remote .

I hope i have been helpful.

Thank You!!

Denon Televison... | Answered on Aug 21, 2010


It is possible that the detect sensors are malfunctioning result in the false trigger of the input detector. So in the first place open the front loading section and clean up the CD take up section. Notice the optocoupler sensors which are the cd detect sensors that could be the culprit in this case. Use a multimeter to check for action on the sensor by blocking and confirming for changes in voltage. If so replace the unit. If not you must also check the mechanism for possible misalingment. remove carefully the mechanism and reset after cleaning. Get help if you are not familiar but be very delicate to do this job if inexperienced. Hope you try with care. Good day

Denon Televison... | Answered on Aug 03, 2010


Hello i have got a all for one remote control and i want to use it for a hitachi freeview box have u got the codes for it plz. thanxs stphen

Denon Televison... | Answered on Feb 14, 2010


From my experience, most of the Denon remotes are universal and do work with each other. If anything, make sure it has a 30 day warranty so you can always exchange it or get a refund.

Denon Televison... | Answered on Feb 09, 2010


with Denon you have to go into the menu and "assign" the inputs.

You have to select if you are using HDMI, s-video composite etc.

If your unit has upconverting remember that it will upconvert a s-video signal to HDMI but not the other way around.

HDMI is a digital signal composite, s-video etc are analog therefore you could not use the HDMI output from your PS3 but then use the red, blue green composite outputs from your receiver to run to your tv.

Denon Televison... | Answered on Dec 30, 2009


Is this a new hook-up? Or have you recently lost sound?
Check your DVD player menus and check to see if it's set for audio over HDMI and not the S/PDIF port.
Some players have an automatic detection for this. It can change just by the order in which you turn the devices off.

Another issue is found in the cables themselves. Although HDMI hardware seems pretty bullet proof There is always a possibility of crappy cables. Try wiggling them to see if has any effect on the sound.

If these fail please respond back with your Denon model # and TV make and model.
Hope it helps.

Denon Televison... | Answered on Nov 29, 2009


l just want the tv code for my tv magnasonic 1992 the remote control name : adr-560

Denon Televison... | Answered on Oct 28, 2009


HDMI won’t pass any signal when the receiver is off. I don’t think you use the same connections before sending receiver for repair. You can connect HDMI directly to TV, and use optical input to receiver for audio only.

Denon Televison... | Answered on Jul 31, 2009


If you're able to turn the player back on and watch a movie be very happy. Otherwise, if the only way to power the unit back on is to open the tray, this is a repair issue. If you bought the unit recently, it should be under warranty--as long as you kept the receipt. However, if the unit isn't in warranty, unless you paid a lot of money for it ($125+) I would suggest replacing the player.

I took the liberty of looking up Denon's warranty. Basically, you have a one year warranty from the date of purchase. If the player has to be shipped, you pay the shipping to the service center and they pay the shipping back to you. You have to have the receipt in order to take advantage of the warranty (you're required to send a copy of the receipt with the player.)

Denon Televison... | Answered on Jul 11, 2009


You have to go into your 'HDMI' audio settings tab, and select "2 Channel".
Once you have selected "2 Channel", then when you go into the 'Audio Setup' tab (different tab then the HDMI audio tab), then they will no longer be greyed out. You can then change it to Multi Channel and they will now all work. I had this problem too, when I first got my 2910. If you are using HDMI for watching Movies etc, then you will need to put the HDMI audio setting back to Multi ...when you are done using your Multi Channel analog outputs

Denon Televison... | Answered on Jun 04, 2009


used single composite video plug to get back to setup.all is good again

Denon Televison... | Answered on Dec 26, 2008


Check the caps on the 12v 5v side

Denon Televison... | Answered on Aug 28, 2008


yes!i am in the d,v,d manufacturing feild and i have seen most every problem you can think of,the problem you are having is generaly caused by despersing of the laiser leens,knowing as high birfrengance some of your light sectors are escaping due to loss of light,replace leens,or replace unit.

Denon Televison... | Answered on Aug 14, 2008


Digital source in
in the setup menu choose the same digital source in


if it dosent work
tell me how the connections have been done

Denon Televison... | Answered on Jul 16, 2008

Not finding what you are looking for?
Denon AVR-1513 Logo

Popular Tags

24 questions posted

Ask a Question

Usually answered in minutes!

Top Denon Televison & Video Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

The Knight
The Knight

Level 3 Expert

76466 Answers

 Grubhead
Grubhead

Level 3 Expert

5700 Answers

Are you a Denon Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Denon Televison & Video

  • Denon Televison & Video

Most Popular Question

unit not powering

  • Televison & Video
Loading...