20 Most Recent
Motorola MTX9000 RMN5038A Remote Speaker Microphone with Emergency Button - Page 9 Questions & Answers
I need remote codes for a src-300a to a toshiba tv
One of these three codes should work: 0156, 0060, 0154In addition, here are the commands to get your remote into programming mode should you require them.
- Press the LED button and hold it down until the LED Flashes.
- Press the REC button. The LED stops blinking at this point and stays solid.
- Press and release the POWER. The remote is now in TV Code Scan Programming Mode.
- Press the UP ARROW (above SELECT) button to scan
through all the TV codes. When you reach the correct TV code, the
TV will automatically turn off.
- Press the SELECT button to store the TV code. The LED flashes rapidly then stops, indicating code has been stored.
12/26/2011 2:27:20 AM •
Motorola...
•
Answered
on Dec 26, 2011
Tv remote code.need the code to work my gateway
It's better to specify the particular model so i can easy help you find codes on your remote control,any way,i'll give you this link and just look for the right model of your TV and download it's manual or code.
CLICK MEGood Luck...
9/22/2011 11:14:14 PM •
Motorola...
•
Answered
on Sep 22, 2011
The switch has turn offed.
please
Hello,
your question is not clear.
what is the model and make of the unit that you want to learn how to turn on?
I look forward to your reply.
Bye for now.
9/11/2011 8:31:43 PM •
Motorola...
•
Answered
on Sep 11, 2011
I have a Motorola "smart
Hi
The possible four digit remote universal remote codes for Motorola TV are:
0020 0003 0093, 0055
Three digit codea are: 003/ 173
OK.
7/10/2011 4:01:08 PM •
Motorola...
•
Answered
on Jul 10, 2011
How do i hook-up my vcr to my cable dvr to record
Hi,
In order to record from VCR to DVR You need to connect "VCR audio/video output RCA jacks " to" DVR 's Audio / Video Input RCA jacks.. ..
use either "RCA analog (red/white+ yellow ) " or
"optic " cable.(any standard optical cable )..if exist .optic is the best way to
connect it..Remember your VCR 's "OUT" goes into" IN "of DVR ..
pls also
remember,wherever you connect your VCR on your DVR ,you should switch
the source selector accordingly to correspond to the connection on the
back...
Now you can record anything on DVR which played in VCR ..
Hope this helps!..if more help requires pls let me know.
Take care and please Remember to rate/vote and give me 4 Thumbs Up for me to continue for Helping out the Community :)
my vcr to my cable dvr to record
6/30/2011 9:09:27 PM •
Motorola...
•
Answered
on Jun 30, 2011
Any solution for water (about
Hello,
yes, there is a chance that the unit is going to recover. For now, don't think of powering the unit. Powering it will damage it if it hasn't gotten damaged already.
Electronics hates water or liquid of any kind, so the unit has to dry 100% before it can power up again.
Leave the unit and allow it to dry more and be rest assured that it is going to turn on again.
You can disassemble the unit, remove the board so that it can dry more. Or if you cannot disassemble the board, leave the unit opened and allow it to dry.
Good luck.
6/22/2011 5:59:50 PM •
Motorola...
•
Answered
on Jun 22, 2011
Ref: Motorola DCH3200 Problem with channel input.
Unplug the comcast digital box and wait 20 seconds or so, then plug it back it. I had the same problem and was given this solution and it worked. NOTE: the program guide will require at least 24 hours to "fill up" again. I was told that the problem is that the cpu in the digital box gets overloaded and needs to be rebooted/reset.
Hope this works for you
5/22/2011 10:05:47 PM •
Motorola...
•
Answered
on May 22, 2011
Not finding what you are looking for?