20 Most Recent Dacor ECS127 Epicure Electric Single Oven - Page 9 Questions & Answers

0answers
0helpful
2answers

My dacor oven light won't

Sorry to read about your problem, I hope this helps you out.


you have a defective door switch

I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck
1/12/2011 8:10:50 AM • Dacor Ovens • Answered on Jan 12, 2011
0helpful
1answer

Will not heat after cleaning

Check that the element has not been dislodged from the socket.
1/8/2011 1:09:17 AM • Dacor Ovens • Answered on Jan 08, 2011
0helpful
1answer

Dacor oven erd30s06ch/lp/h electric lower

Hi,


If your electric oven is taking too long to heat or just not heating up right, then check out this tip that will give more detail about your problem.

Oven Problems Electric Oven is Heating Slowly or Poorly

heatman101

12/26/2010 12:53:54 AM • Dacor Ovens • Answered on Dec 26, 2010
0helpful
1answer

After oven turn on

F1 means the system watchdog cicuit has detected a fault.

Try pressing CANCEL for 30 seconds if it continues after that you will probably need a replacement control board.
12/13/2010 2:54:21 PM • Dacor Ovens • Answered on Dec 13, 2010
0helpful
1answer

PCS 127 does not heat up. Fan and preheat start.

We were able to unscrew the plate that sits behind the latch. 6 screws I believe. Look towards the middle back-right side you will see a red switch. Click it twice. Before we put plate back we tested oven and it worked!!! Hope this info will help you. Dacor oven has been a real problem and I'm a kitchen designer. Will never recommend Dacor anything to my clients after many oven issues.
12/12/2010 10:53:03 PM • Dacor Ovens • Answered on Dec 12, 2010
0helpful
1answer

Thermomator sensor Use instructions

Please, send us details about your specific model and additional description details about your problem.
11/25/2010 8:53:25 PM • Dacor Ovens • Answered on Nov 25, 2010
0helpful
1answer

The oven keeps blinking F2

F2 Heating mode high temperature This alarm is activated when the ERC senses a runaway heat condition or when the temperature exceeds "runaway limits". The ERC will beep until the cancel or another function is selected. If the alarm repeats the F2 code check the oven sensor and wiring after first checking for a stuck relay. If alarm goes away verify the oven will complete a clean cycle without any type of failure.
11/25/2010 6:21:50 PM • Dacor Ovens • Answered on Nov 25, 2010
0answers
0helpful
1answer

The cooling fan on model

Yes , there is a cooling fan located at the top of the oven
It could be the fan blades catching, or a noisy fan bearing.
You would have to access it by removing the top oven cover to check., and yes it could be as a result of having it cleaned.
Plz rate my solution.
Thanks.
10/25/2010 2:47:53 PM • Dacor Ovens • Answered on Oct 25, 2010
0answers

Hi We have a

Be the first to answer 10/24/2010 12:49:05 PM • Dacor Ovens • Posted on Oct 24, 2010Be the first to answer
0helpful
1answer

New MORD227 installed yesterday.

You might have missed some procedures in between. You can use the user manual that came along which describes how to use the model, in the best way possible, including diagrams. Since it's under warranty, don't attempt any of those repairing measures, if suggested by any other expert. If you are not so confident of doing it yourself, you can contact the dealer, who will provide you a company repairman for free. He will teach you everything fine. If you have a habit of forgetting things, try noting it down somewhere.
Cheers. Thank You.
10/16/2010 11:36:44 AM • Dacor Ovens • Answered on Oct 16, 2010
0helpful
1answer

Clock runs continuously 24 hours

This is definitely just a setting on the unit but I need to know the make and model of the unit to get it fixed for you. What is the make / model?

Thanks
Tim
10/5/2010 3:40:25 PM • Dacor Ovens • Answered on Oct 05, 2010
0helpful
1answer

When I cleaned the Convection

Hi,

F2 message shows appears because the heating sensor as sensed high temperature.When the ERC senses high temperature then You will get F2 error.Some times alarm beeb will go on.The ERC will alarm and show F2 until the cancel or another function is selected.This is to intimate the oven temperature is beyond level so please let it cool down.


Don't worry this is like error code and for your information it showed up.

post a comment for further assistance.
Thank you for using fixya have a nice day:-)
9/8/2010 5:01:36 PM • Dacor Ovens • Answered on Sep 08, 2010
0answers
0helpful
1answer

I am looking for an

8/17/2010 10:35:34 PM • Dacor Ovens • Answered on Aug 17, 2010
0answers

Hi I have a decora

Be the first to answer 8/17/2010 10:11:03 PM • Dacor Ovens • Posted on Aug 17, 2010Be the first to answer
0helpful
1answer

Oven Model CPS130S, purchase 1994,

dacorservice.com/PartsCatalog/docs/Wall%20Ovens/.../PM_CPS_CPD.pdf
parts catalog above.
Technical manual below.
www.scribd.com/doc/14008662/Dacor-Technical-Manual -

Most likely your electronics have been "Spiked" and you will need to replace this control pad.
Due to the age I myself would be in two minds as to repair or replace?

8/11/2010 3:59:25 AM • Dacor Ovens • Answered on Aug 11, 2010
0helpful
1answer

The oven door will not

Hi

Disconnect the electrical power. Turn it off at the panel breaker to the kitchen appliances or plug out the electrical plug from the wall outlet.

Once you do this, allow power to be off for about 15 - 20 minutes. Supply electrical power back to the appliance.This will reset the internal circuit.

If that does not work and the door has a lever which you move to the closed/open position, it may be jammed, bent slightly or forced closed to much. Wiggle it genitally as you attempt to open/release the locking device.You may have to remove the front glass panel to access the locking device. Be sure electrical power is off before doing so.
OR did you ran the self-clean…

1. Let it cool down and it should open, if not.

2. Unplug the unit or shut off the circuit breaker for 5 minutes. Plug the unit back in or turn on the circuit breaker then try moving the door lock lever or opening the door if there is no lever.

3. Set the self-clean cycle again and only allow it to work for 15 minutes. Cancel the self-clean cycle and allow the oven to cool. Try moving the door lock lever or opening the door if there is no lever.

Please check the link bellow…

http://www.appliance411.com/faq/cleanlock.shtml

Let us know if you have something more to know else accept the suggestion.
Thank You for contacting Fixya.com

8/5/2010 3:23:47 PM • Dacor Ovens • Answered on Aug 05, 2010
Not finding what you are looking for?
Dacor ECS127 Epicure Electric Single Oven Logo

Popular Tags

36 questions posted

Ask a Question

Usually answered in minutes!

Top Dacor Ovens Experts

Jaime Hernandez

Level 3 Expert

2351 Answers

Paul Bade

Level 3 Expert

1744 Answers

Ngoro

Level 3 Expert

3511 Answers

Are you a Dacor Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Dacor Ovens

  • Dacor Ovens

Most Popular Question

f1 mean

  • Ovens
Loading...