20 Most Recent Dacor ECS130 Epicure Electric Single Oven Questions & Answers

0helpful
2answers

My dacor oven model ECS130SBK

I found the bottom element was not getting any power by using a volt/ohmmeter and a test method described elsewhere. (Shut off power, hold down COOK TIME while turning on power. then within 30 seconds press each mode you want to test and only that element/fan/etc will turn on. Cancels by itself after 30 sec.) I traced the wire back to the relay (wire checked good) and there was no power getting through the relay although it clicked. Removed the relay board to replace it and found a cold solder joint on the "out" terminal with obvious past arcing carbon. Cleaned and soldered the pin and the oven now works normally.WHY THE SLOW TO HEAT? The oven turns on all the elements to preheat faster and when it reaches your set temp it beeps and now only turns on the element you selected to maintain the temperature. (Bake or Convection) Our malfunctioning ovens would then cool since the element is not working properly and it must go back into preheat and keep cycling. BY THE WAY- Don't ever use 4 hours on self clean it kills the boards and/or display. I also put a house fan in front of the oven and blow it into the lower grill to take away some of the heat on the two boards. Learned the hard way!
4/24/2018 5:08:12 AM • Dacor ECS130... • Answered on Apr 24, 2018
0helpful
1answer

Dacor

chk the spring and the door hinge. it is probably the hinge-spring that is broke, or slipped out of the hinge. lol.
4/27/2014 4:50:28 PM • Dacor ECS130... • Answered on Apr 27, 2014
0answers

Door

Be the first to answer 4/27/2014 4:08:58 PM • Dacor ECS130... • Posted on Apr 27, 2014Be the first to answer
0answers
0answers
0helpful
1answer

How to clean

turn off the circuit for the oven and use some wet wipes and clean it. before you run it make sure it is dry.
7/3/2013 1:52:41 PM • Dacor ECS130... • Answered on Jul 03, 2013
0helpful
1answer

Dacor oven beeps and shows F1 code

-F1- Alarm “System Watchdog Circuit”
The system will detect a failure in the internal watchdog element relay circuits and will activate a
cancel feature. F1 will be displayed in the time digits and will beep until the cancel button or another
function is selected. An F1 failure could be detected in cook or time of day mode. With an F1 failure
the ERC is picking up a command to supply heat without receiving an input from the membrane. The
watch dog circuit is designed to prevent this.
If the beep continues after pressing cancel check the main control (ERC)
Dacor
If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61
12/1/2012 9:14:25 AM • Dacor ECS130... • Answered on Dec 01, 2012
0helpful
2answers

Dacor oven takes long time to heat.

DACOR DIAGNOSTIX BABE !!! If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61
8/14/2012 9:01:41 PM • Dacor ECS130... • Answered on Aug 14, 2012
0answers
Not finding what you are looking for?
Dacor ECS130 Epicure Electric Single Oven Logo

102 questions posted

Ask a Question

Usually answered in minutes!

Top Dacor Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Oloyede Monsuru

Level 3 Expert

1468 Answers

Paul Bade

Level 3 Expert

1688 Answers

Are you a Dacor Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Dacor Ovens

  • Dacor Ovens

Most Popular Question

dacor oven model ecs130sbk

  • Ovens
Loading...