20 Most Recent MTX T-Form04-05 Chevy Colorado Gray w/10'' sub Car Speaker - Page 7 Questions & Answers

Sounds like the subs are blown with the voicecoils fused together which means the amp is/was seeing a dead short ( zero Ohms reisitence) not good for any amp. Disconnect the speaker terminals from the amp and see if it turns on. The funny smell might have been the subs blowing up, i'll keep my fingers crossed for you.

run all three positive to negative and bridge them at the amp

you need to change your remote wire to a switched 12volt source, not a constant, run it to your ignition fuse

had a friend with same problem...paid me to look at it and well...amp was just overheated or short/loose ground.

I hesitate to answer this question for fear that you will not like the answer even if it is the truth. I have received a bad rating from a couple of people in the past just because the right answer was not what they wanted to hear.

This is a mono sub-woofer amp, which means that it is already bridged internally. You only have one speaker output in this amp, that means that the amp circuit is bridged inside, it is not split into two channels.

To bridge any output, it requires 2 channels, otherwise there is nothing to bridge.

I have been repairing car amplifiers for over 18 years, and I promise you that there is no way to bridge a single channel amp. Bridging means to convert 2 channels into 1 channel. If all you have is one channel, then there is nothing left to bridge.

I hope this explains it for you, if you have any other questions feel free to post them here and I will answer as soon as possible.

And please do not punish me with a bad rating if you do not like the answer, it is the correct answer, and sometimes the right answer is not always what we want to hear, but it does not make it wrong.

Dave

There are several things you can check. Do you have a multi-meter?

This site well be helpful for you to configure the connections
http://www.the12volt.com/caraudio/boxes.asp

connectors on the rca's are bad. need to be changed out

i have seen the jackhammer at autobarn moss street slacks creek brisbane qld not sure if it is 12000 watts but looks massive you could also try gold coast car sound brisbane qld

what amp are u usin?What enclosure 4 speakers do u have?Might not have enouigh voltage 4 the amp.How big are the wire for power 2 amp?what ohm are you playing ,is it compatible to the woofers.Need more info.Model and makes please,but 1st a rating.

check you spkr wiring in put if they are cross

How to change language to english for Honda Odyssey 2021 Gathers Radio Player

I have the same radio now with no Bluetooth am trying to get Bluetooth on it too without having to buy another radio. Please help.

First thing to do is check to make sure that the batteries are properly charged.

Second, make sure that you have a clear line-of-site to the IR transmitter. Infrared (IR) works the same way that your TVs remote control works - if the signal is blocked, then you will not hear any sound.

Third, make sure that you are in the rear seat of the vehicle when listening to the sound. The IR transmitter only transmits to the rear seat, so you will not hear any sound if you are sitting in the front seats. This is a common problem that i see.

Lastly, make sure that the heapdhones you purchased are compatible with your 2006 2007 2008 2009 or 2010 Toyota Sienna. Remember that some older models require RF headphones, not IR headphones. I checked http://www.audiovideo2go.com for compatibility before I purchased my headphones. They have a useful listing of all the headphones and models of vehicles they are compatible with.

'make model (what is is)' as first 3 words in all questions. https://www.google.com/search?q=demo+mode+the+code+for+4.91 ..

Unfortunately, no one knows or is telling. Companies rarely state power in RMS because Peak Power is a much more impressive. 1000 watt amp, 200 watts RMS x 2 channels at 8 ohms. Look for a sticker on the unit. https://www.google.com/search?q=Xplore+Amp+5553 ..