20 Most Recent
Questions & Answers
My px700w epson printer has
Is it show general error?
Your printer's problem is in a sensor that is situated the opsition of the printer head. Try to clean it. Totaly deassemble the head carriar and then see it's opposite. there is 2 too little hole jast like a little incect eyes. These is the culpit. Clean it with soft tissue or soft painting brush.
I think you may relive from your printer problem.
I have a Mac Book. Recently installed an
First of all, check to make sure your printer's USB cable is securely connected in your Macbook's USB port.
Next, make sure your Epson SX515W has the latest drivers installed for your current version of Mac OS X
Mac OS X Drivers for Epson SX515W
If you already have the updated printer drivers for your Epson SX515W already installed,
go into System Preferences> Print & Fax and see if the printer is displayed in the Printer window. If it is, click the "-" Minus button and remove your current printer.
* Click the "+" Plus button and re-add that printer.
Once you do, make to set it as the default printer.
- Now attempt to print a test page from any document you have.
See if this does the trick. If if does not, just let me know.
CANON PIXMA IP1200 resetting
My converted iP1200 is currently blinking green, yellow, green, yellow on the power lights after start up and print request. The pop-up prompt suggests turning off the printer and turning it back on. Error 5100 is always seen.
Please Help Me...
Epson stylus cx 7400
Epson includes step-by-step instructions on changing the ink cartridges in the Printing Preferences menu:
Click the start button and open the Control Panel.
Right click Printers and select Printing Preferences.
Click the Maintenance tab.
You should see a button that says Ink Cartridge Replacement.
Just follow the instructions and it walks you through it.
Urgent: red light error on Epson Stylus CX3650
It appears that this is an overseas model (at least for those here in the US that is) as far as I can tell. This will use the same drivers as the CX3600 model though. Depending on how long you have had this and how often you use it, you may have a waste ink reset situation. While I have not had any personal experience with this model, there are several references on the internet on how to do a reset. There is even an "SSC Service Utility" you can search for that lists this printer as being supported. It cannot reset the ink counters but it may reset the waste.
Good luck, I hope this is of some help.
I need some software for resetting epson cx 5500, please ?
Print Cartridge Problem- HP PSC 1513
which cartridge is giving you problems? The one on the right? I think that is, IIRC, the black ink. Is it out of ink? If so, go to OfficeMax or Walgreens and have it refilled, or buy a new one. If it is clogged, then run your toolbox utility to clean it.
Receiving faxes with a Cisco ATA 186
More investigation implies that faxing over VoIP, as I am doing, requires setting the fax BAUD rate to 9600 bps or slower. So does anyone know if it is possible to set the BAUD rate on the Dell MFP 1600n multifunction printers?
Epson Sx200- Paper wont feed
Just a thought,as I had a similar problem.The instructions are abysmal,but it may be worth having a look where you feed the paper in and squeezing the grey plastic gizmo,and moving it to the left to allow the paper to enter the feed properly.
Remove ink cartridge
I found that the proper way to do it only worked when the ink light was flashing red. Then when I pressed the stop button it moved across and stopped beneath the marker to show which cartridge needed changing. The I pressed the stop button again and it moved to a place where I could change it.
This happened despite the fact that the pictures I was printing blatently showed that I needed to replace my ink, it wasn't until I had printed the liney pictures a few times that the printer decided the ink level was low enough to turn the flashing light on and let me change it.
Cartridge holder won't move when i press button to change ink
Hi, it's not ready for a replacement cartridge yet, the printer is only LOW on ink not OUT of ink. continue to use the printer until the flashing red light remains on solidly, then the head will move to the replace cartridge poswition when you press the button.
Not finding what you are looking for?