NComputing L230 Network Terminal - Answered Questions & Fixed issues

First Please check your Lan IP Address for host pc.
change IP address and subnet mask on L230
disable firewall or any antivirus that is blocking ports.
Then you will get connected.

my present solution is to restart the host PC.

SARATH BABU Simple press ctrl + shift + end key if its ask password

For security purposes, this process cannot be disclosed in an online guide. For assistance resetting an L-series firmware password, please contact NComputing technical support directly at http://www.ncomputing.com/techsupport

Hi!

Please download and install the latest software for your operating system from here:

http://www.ncomputing.com/softwaredownload

Hope it helped.

All of them.

check the network cable

download from ncomputing website they have it for win 7

a problem with your network cable.try to climb again

change your keyboad

Here's a video Nitin Sharma suggested as a solution to your problem from YouTube:


NComputing L300 Ethernet Virtual Desktop

If your existing LAN has DHCP assigned IP addresses, you will be good to go. If you have statically assigned IP addresses, you will need to enter them in manually into the device. Their website has a very good instructional video on the procedures to hook up the devices. It will work with standard cat5,cat5E, or cat6 wiring.

Please reimage your terminal to factory settings. Necessary software is available from ncomputing at http://www.ncomputing.com/support/software-downloads

a fixed ip address while password protected the gadget

you will need to open up your network connections click start control panel network connections this may vary depending on your operating system look for local area connection if you see a red X or a yellow exclamation or question mark ! ? you will need to update or install the driver or it could be firewalled click start control panel administration tools computer management device manager scroll to network adapters should see a yellow question mark? right click install drivers the driver might be on the disc supplied by your ISP internet service provider or the motherboard disc or you might download one if you dont have on a disk

Make sure you Ethernet is enabled in bios restart your computer during the boot up process you will see on your screen a certain key to

press to enter set up (BIOS) press and hold that key to enter bios using arrow keys scroll to intergrated peripherals

look for SiS On Chip Pci Device press enter scroll to SiS 10/100m press enter make sure its enabled hope this helps

if you dont have a motherboard disk or a disk with the drivers you will need to download them http://download.cnet.com/2000-20_4.html on the home page you should see a search tab just type in what you are looking for

IE: motherboard name ethernet driver you might have to try a few times to get it right

hope this helps

Hi

Not clear whether you installed SP1 on the client or the server.

Try resetting or powering off and on the L230 and let it reintroduce itself to the network.

Also restart the computer that had the SP1 installed on it.

If none of the above resolves the problem, enter Network settings on the client and ensure that Neywork Discovery and File Sharing are not turned off. If they are off, enter Network and Sharing Center and use the Drop Down arrows on the right to turn them and any other desired options on.

Hope this helps.

Simply register your vSpace software, the registration wizard is part of the Program group.run that registration, takes less than 90s, and make sure you enable background hardware activation from the vSpace Console, system settings.

Since you posted this four months ago, there has been some major updates from NComputing to improve the USB architecture. This should improve support for peripherals such as your printer. Download the latest software for either W2K3 (v4.9.5) or W2K8r2 (v6.1.3) and update your system. Lastly, it is critical, and I mean absolutely critical, that you update the firmware on the L300 as well. The firmware is included with the vSpace update so once the host is updated, go to the L300 and tell it to update the firmware. The current firmware version that works with v6.1.3 or v4.9.5 is v1.4.1. As of this writing, 8/16/11, those are the current versions.

Make sure you're on the latest vSpace software for W2K3, that version is v4.9.5 and is available on their download site. The issue you mentioned will be resolved if you update your software and register it. Make sure to enable bakground hardware activation in the system settings. That's managed through the vSpace console.