Top 20
Just Wireless Bluetooth Headset - BT-38 - Page 8 Questions & Answers
I need to program ic-f3gs-2 radio
Even saying ICOM would help people to help you. That radio requires software and a programming cable adapter. It is new enough to do Narrow band. Best bet is to find an ICOM dealer to program it for you. That way, it will be on legal frequencies. Your unit is VHF, so it cannot talk to GMRS over the counter radios. It is a decent radio, we sold them and the battery life was good. Ask more if you want to know more.
10/30/2019 1:09:53 AM •
Radio...
•
216 views • 0 helpful votes
How do I fix my BAOFENG UV-5R Radio?
try to do a Hard reset on the unit and then reload your freq list from Chirp. It happened to my UV-5R-v2 Baofeng. It worked fine after that.
9/24/2019 10:16:38 PM •
Radio...
•
570 views • 0 helpful votes
My KSC-35S UHF radio has constant background static,can it be squelched ?
Your Kenwood radio has programmable squelch. It is accessible through the software. However, if the squelch knob (pot) has been broken, it must be fixed or replaced. Move the control knobs back and forth, do either move more than say 1/16 of an inch? If so, they likely broke inside. You could open the radio, resolder the switch, which I called a pot and see if that works. If not, take it to a dealer or sadly, buy another radio.
10/18/2019 10:02:51 AM •
Radio...
•
251 views • 0 helpful votes
I cant get headset to pair after replacing battery.
You might have to reset it, that is if it paired before with the same device. Know that Blue Tooth has different versions and some don't work with other versions of bluetooth. But your post sounds like it worked before you reset it, so it may just be that easy.
10/20/2019 11:39:41 PM •
Radio...
•
160 views • 0 helpful votes
Squelch wont stop bc350a
you may have a bad squelch pot on the radio. try turning it fully in one direction an back in the other direction. it also could be that the Pot is dirty get some contact cleaner and open up the radio and squirt a very little cleaner into the open spot of the Pot. then rotate the know several times. if you do not have something like CRC QD Contact Cleaner you can get it in a good hardwood store like ACE or TrueValue, and even Home Depot. you can use only 91-99% Electronic Grade Isopropyl Alcohol, do not use the 70% Isopropyl Alcohol.
10/3/2019 5:16:34 AM •
Radio...
•
250 views • 0 helpful votes
Can't Get Bearcat 248clt scanner to Squlech
Make certain the AM/FM radio is off. You cannot squelch when it is on. Try adjusting again. If it does not stop the squelch noise, the switch is dirty or broken. To go further means taking it apart. You will try to "clean" the switch. Do you want to take it apart?
10/22/2019 12:35:48 PM •
Radio...
•
138 views • 0 helpful votes
Can I pair my Foxtel iq4 with other devices like Bluetooth earbuds?
Unfortunately, no. Although the Foxtel iQ3 and iQ4K STUs do have Bluetooth functionality built in, it is only used for pairing a compatible Foxtel remote control - Bluetooth audio is not supported. You will need to pair your headphones with your television set which will transmit audio from the Foxtel STU via HDMI.
7/5/2019 6:16:51 AM •
Radio...
•
2,944 views • 0 helpful votes
Why does mic stay open all the time on my rugged radio in my atv
The usual cause is that the transmit button on the mike is broken or stuck in the "talk" position. If you disconnect the mike and the radio, then turn the radio on and it still is showing transmit, then the issue is inside the radio or the connector for the mike.
If the radio stays in receive mode with the mike disconnected, look at the mike connector for any bent pins or damage to the connector. If you don't see anything, try spraying electronic contact cleaner , the could be some corrosion that is causing a short here. Another thing, if you have it, is to use a different mike and see if that works properly.
9/16/2019 4:34:13 AM •
Radio...
•
335 views • 0 helpful votes
Do the headset got a reset button
Most headsets do not have a reset since there is nothing to reset. If you need to pair it again with a phone, go into the settings of the phone, find the bluetooth device list and tell the phone to forget the headset. then do the pairing again, after fully charging the headset.
9/17/2019 11:25:51 AM •
Radio...
•
170 views • 0 helpful votes
Not finding what you are looking for?