Washing machine works OK, but it collects smelly water trapped behind the gasket seal of the front door. Any way to fkush out th water. We tried a spin with the machine empty.
Posted by norman1000 on
Frigidaire has several mfr defects with their new front loading machines. The detergent/bleach drawer retains water, the door often leaks, water does accumulate in the door seal and the spin has broken twice on us and the machin is only 15 months old! Repair is contracted out by Lowes to independant repair companies, who demand payment, even when Lowes says it is covered under warrantee. What a waste of a large amount of money! We will NEVER purchase Frigidaire or recommend their products to anyone.
Posted on May 11, 2008
I have a GLTF2940ES3 front loader. It is a bit over a year old. Today we went to take the clothes out and they were soaked. We tried running drain/spin, rinse/spin...nothing. It does everything except the high speed spin. Water drains fine..."whirring" noise when it should be spinning....we tried lessening the load too, and nothing. Please help!?!?!? I have a GLTF2940ES3 front loader. It is a little over a year old. Today we went to take the clothes out and they were soaked. We tried running drain/spin, rinse/spin...nothing. It does everything except the high speed spin. Water drains fine..."whirring" noise when it should be spinning....we tried lessening the load too, and nothing. Please help!!!!!!!!!
Posted by anlopez375 on
The problem is a faulty Door Latch Assembly. The same thing happened to my Frigidaire front load washer. The part is easy to install, costs about 60 dollars and can be picked up at most appliance repair stores . To access the switch just remove the wire around the front drum gasket, peel back the rubber gasket beside the switch assembly then remove the two screws holding it in place. remove the three wire connector blocks and swap in the new switch. My washer was giving me error code 41 witch is a faulty control board. But the problem was in fact only the switch...
Posted on Dec 28, 2010
what does EFO code mean on our washing machine?
Posted by asiler240 on
Frigidaire, Zanussi, AEG, & More....
EFO = Filter Blocked (low flow) and it is accessible from the bottom front of the machine.
1. there is a blockage in the filter or drain hose.takes too long to drain out.
2. over dosing of powder or liquid. again can cause an air lock in the pump which slows the drain pump down.
Check the filter and drain hose and test again. this fault will only come up at the end of a cycle.
You do not need to reset the machine to get rid of the fault code as this is automatically deleted.
Run an empty load with no detergent in an attempt to get rid of the code.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
Posted on Sep 16, 2010
my Frigidaire front load washer keeps beeping even when there is not a load in it
Posted by mofla1222 on
E70 error code repeatedly comes up when attempting to start a load and you have to cancel and restart 4-6 times before the load washes; again at the end of a load it will come up with the E70 error and to complete the load you have to set it on drain and spin only setting. I even downloaded the tech manuals and an E70 is not even listed! HELP!!!
Posted by JWilkerson on
Means you are not getting cold water into unit..Either cold water hose is connected to the wrong hose or cold water faucet is not turned on..You can solve this by connecting hose to cold water faucet and cold water inlet on washer..
Posted on Nov 06, 2007
Started to beep and flash EFO...what does it mean? flashing EFO error code
Posted by EDDIEWILLI... on
spoke with electrolux and they tell me that it is over sudsing problem. The washer must use HE detergent or use only a the lowest amount on the cup.
Posted on Sep 17, 2008
My washer is displaying the DDO error code. Please help?! I am not sure what this means and my washer in not working at all now. Do you happen to know what the problem might be? Thank you-
Posted by northernwi... on
Excellent solution. I had a similar problem. The trick is to figure out where to put the magnet. I had a hard time with that.
For those like me who might have difficulty finding the spot for the magnet, it goes on the right hand side of the detergent door. The easiest way to do it is to pull the detergent door all the way out of the machine and look at it such that the back of the door is facing you. The magnet fits vertically in a slot on the left side as you are looking at the door (right side of the doorwhen inserted in the machine) in the white plastic. It sits vertically and is held by a small latch. This is not obvious at all...
Posted on Jul 13, 2008
My machine stopped on a washing cycle with code E23 and two beeps. It makes a humming noise when i try to start the cycle. There's water in the compartment not being drained. What's the solution?
Posted by nzkhan on
Hello welcome to Fixya
The drain pump relay on the control board has failed.
Fix: Replace control board or wire!
you can see schematics and diagrams at the site below, and order parts from them if you want.
Or call service!
Thank You For trusting us with your question
Please remember to leave a solved rating before you leave!
Posted on Dec 25, 2008
Frigidaire Front load washing machine starts, squirts water then stops. Have replaced control board and still have problem and get error code E5E. Also recently replaced door switch assembly.
Posted by cyndy_doug on
E5E IS FOR Communication problem. THERE IS 100 %WIRE SHORTING SOMEWHERE.PLEASE CHECK OUT.
ALSO OTHER ERRORS Error code - Fault condition
E11 Fill time too long.
E13 Water leak in tub or air leak in air bell.
E14 Reed switch.
E21 Water not pumping out fast enough.
E23 Drain pump relay on control board failed.
E24 Drain pump relay on control board failed.
E31 Better models. Pressure sensor not communicating with control board.
E35 Better models. Pressure sensor indicates water overfill.
E41 Control board thinks the door switch is open.
E42 Door remains locked after cycle is completed.
E43 Control board problem.
E44 Control board problem.
E45 Control board problem.
E46 Control board problem.
E47 Board thinks the door PTC circuit is open in spin.
E48 Board thinks the door PTC circuit is closed.
E52 Bad signal from tacho generator.
E55 Motor overheating.
E56 High motor current.
E57 High current on inverter.
E58 High current on motor phase.
E59 No tacho signal for 3 seconds.
E5A High temperature on heat sink.
E5B High temperature on heat sink.
E5C High temperature on heat sink.
E5D Communication problem.
E5E Communication problem.
E5F Communication problem.
E67 Input voltage on microprocessor incorrect.
E75 Better models only. Water temperature sensor circuit.
E76 Better model only. NTC temperature for the cold water valve over the limits.
E95 Communication error.
EB1 Incoming power frequency out of limits.
EB2 Incoming line voltage above 130 VAC.
EB3 Incoming line voltage below 90 VAC.
EF1 Clogged drain pump.
EF2 To much soap.
Posted on Nov 12, 2008
Everytime I put fabric softner in the dispenser it never drains during the wash and stays in the dispenser. What am I doing wrong?
Posted by cyndie on
Remove the dispenser tray. Inspect the area just above the fabric softener portion of the dispenser. There should be a series of holes where water feeds into the tray during the rinse cycle. Sometimes these holes become clogged with fabric softener residue. If the holes are clogged, water will never dispense the fabric softener out and it will stay in the tray. If you take some cotton swabs and meticulously clean all the holes out, I bet your problem will go away. Let me know if this was helpful to you.
Posted on Oct 06, 2007
1,216 questions posted
Usually answered in minutes!