Frigidaire Gallery GLEFM397DS Electric Kitchen Range - Page 4 - Answered Questions & Fixed issues


Check the gap on the side of the door. Most likely the top will be wider than the bottom. There is a bulliten for several models. Call a service/parts dealer. Give them your model and serial number they can check the bulliten and order the correct hinge kit. The hinges and receivers will need to be replaced. Both must be replaced to correct problem. Not a difficult repair. If no one will hepl you, respond back and I can check the bulliten and get you a part number. And can order and ship you a part if necessary.

Frigidaire... | Answered on Apr 18, 2009 | 226 views


Your oven ignitor has gone out. This is located under the pan in the bottom of the oven. This is held in with 2 screws in the back portion of the pan. This will expose the ignitor and then 2 screws take it out. Replace this and this will fix it. very common problem

Frigidaire... | Answered on Mar 21, 2009 | 949 views


well the person at frigidaire was talking about caustic chems like easy off elements should be ok get as much of the silicone and foil out as you can then run self clean only prob i see is the oder the oven wilkl self clean for three hours send the misses and kids to a movie get you a six pack of brew sit on the front proach depending on where you live and let er rip then lets see what to do from there how much stuff you got stuck on there

Frigidaire... | Answered on Jan 31, 2009 | 507 views


These doors have springs to shut them. If you can figure out how to get to the springs usually you will see that one is either unhooked or unattached at one end. If broken on the end bend another hook into it and add a pice of wire long enough to make up the broken difference. 

Frigidaire... | Answered on Jan 02, 2009 | 514 views


F0 & F1 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control)

Frigidaire... | Answered on Aug 05, 2008 | 461 views


F0 & F1 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control)

Frigidaire... | Answered on Aug 25, 2008 | 940 views


The model number should be posted on a nameplate near the oven door opening and/or lower drawer opening (if equipped). Sometimes the model number is located along the back of the operator console. You will need this model number in order to ensure you are getting the correct manual as all appliances are not the same with operation and features. Go to geappliances.com and click on the "Service and Support" link. On the next page is a heading for "Use and Care Manuals". Click on the link, type in your model number, and there should be a manual available for you to download in .pdf format (Adobe). I hope this helps you.

Frigidaire... | Answered on Aug 01, 2008 | 182 views


The oven features on electric ranges are controlled by the Electronic Oven Control (EOC) board. Commonly referred to as the clock assembly. Each function (bake or broil) is usually controlled by a separate circuit. If you have installed the new element, and can rule out the possibility that you may have received a defective part, the EOC may be a likely culprit. Before you go tearing the console apart, however, double check your wiring on the element you just replaced and take a resistance check of the element. Measure on the element terminals with the wires removed. The reading should be in the K ohm range (resistance will vary between manufacturers). Then measure from one of the element terminal to the outer shell of the element. If it reads a short (0 ohms) you have a grounding problem and probably have a bad element. If you are confused by any of this, please post back with any questions you may have. I hope this helps you.

PS There should be a tech sheet inside the operator console to assist with troubleshooting.

Frigidaire... | Answered on Aug 01, 2008 | 217 views


The same thing with mine. I took apart the door today and found the hinges a little bent. I think it should be ok to bent them the opposite way a little with some mole grips......and then I must remember not to move the stove out for cleaning by the oven door handle again (oops).
Door comes off (unlock hinges and lift up). undo 4 screws on the bottom edge and then two on the inside of the door handle then it comes apart - beware as it's heavy. The hinges themselves come off with two screw each.

Frigidaire... | Answered on May 25, 2008 | 588 views


lock mechanism is acting up. happens sometimes. you can get to it from the back and get the thing open to use until you get the part

Frigidaire... | Answered on Dec 08, 2008 | 984 views


the lock mechanism is acting up. if they fail they can give the board a door locked indication through one of the microswitches but not be locked. you can find the assembly under the cooktop and at the back of the unit with a rod going up to the actual latch you may be able to touble shoot it from the back without taking the top off

Frigidaire... | Answered on Apr 22, 2008 | 87 views


There may be a broken spring that helps the door stay open.

Frigidaire... | Answered on Apr 02, 2008 | 297 views


You can try turning the power off for a couple minutes then back on but this is typically caused by a stuck key or a faulty control board. Either way you're looking at needing a new control board.
Hope this helps.

Frigidaire... | Answered on Feb 10, 2009 | 379 views


THERE SHOULD BE A KNOB SELECTON ON THE MAIN TEMPERATURE CONTROL OR SOME HAVE A SWITCH. OR .I DO NOT KNOW WHERE IT IS ON FRIGIDARES ... AND PLEASE DONT HOLD IT AGAINST ME. I WILL SAY THAT ALL SELF CLEANING STOVES DO IS TURN BOTH YOUR BROILER AND OVEN BURNER ON HI AND "BURNS OFF THE SPILLAGE OR DIRT" IN AN ALOTTED TIME. AS A REPAIR MAN I NEVER ADVISE USING THEM ... THEY CAUSE ALOT OF HEAT AND DONT REALLY WORK ALL THAT WEEL IF THERE IS ANY SIGNIFICANT SPILLAGE TO CLEAN ANYWAY.

Frigidaire... | Answered on Nov 08, 2007 | 260 views


Turn off the gas to the house and worry about it later when the fumes have dissipated

Frigidaire... | Answered on Sep 16, 2020 | 11 views


F3 - Open/shorted sensor (RTD probe) connection.
Check the temperature sensor and the wires and plugs between the sensor and the EOC are good, replace the temperature sensor (RTD probe). If the sensor and wiring are good, the EOC would need to be replaced.

Frigidaire... | Answered on Sep 03, 2020 | 147 views


You may have to shim the drawer or the track to get things working again.

Frigidaire... | Answered on Jul 20, 2020 | 108 views


The F11 code may not be related to clock failure. Check with an appliance parts supplier and/or Figidaire.

Frigidaire... | Answered on Jul 08, 2020 | 26 views


Press and hold set clock for 6 seconds. CLO will appear in the display. 2. Continue holding the key until 12Hr dAY or 24Hr dAY appears in the display and the control beeps once.

Frigidaire... | Answered on Jun 17, 2020 | 37 views

Not finding what you are looking for?
Frigidaire Gallery GLEFM397DS Electric Kitchen Range Logo

137 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Kitchen Ranges Experts

Paul Carew

Level 3 Expert

3518 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Are you a Frigidaire Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...