Dynex DX-PDVD7 Portable DVD Player - Answered Questions & Fixed issues
To be more specific the screen is cracked. where
Because this is a budget-design model, the cracked screen could quite possibly make the repair uneconomical, assuming a replacement LCD panel was available for it. However, you can submit the player to any reputable authorised DVD repair centre in or around your area for a quote - but be warned - if you go ahead, it could be expensive, unless you have a manufacturer's warranty or similar. These units are generally not repairable at individual component level, which makes the repair cost prohibitive in a budget model such as this. Up to you.
A new player may cost less than the repair/replacement parts for this one.
With no disk loaded and
Unfortunately the stepper rail linkage is defective that moves the laser pickup assembly, the only solution is replace the whole laser pickup assembly which is not cost effective, cheaper to buy a new portable dvd player.
Screen says "Loading" and will not play DVD. What
Hi lhanlon1,
Try these basic steps below to solve your problem.
You should prepare tools and test instrument like multimeter.
Assuming that the disc is good.
1.Clean the lens. -
Sometimes because of dust the lens can't read any disc. Try clean the lens by
soft cotton buds. Be careful while doing this.
2.Replace the ribbon - Check
the ribbon connected to the lens from the main board for scratch,
damage. Once it has an open line then of course the lens can't read the
disc. Also try to erase the contact by pencil eraser. If you've done the steps
above and the symptoms still there then the next step requires you a little
knowledge in soldering technique and reading the ohmmeter.
3.Check the motor - Check
the motor that spin the disc with an ohmmeter. You can test it using the
ohmmeter (x1) even it is connected on the lens assembly.Good motor - reading
should be fairly high and it will spin. Bad
motor- reading will drop to low resistance and will not spin. You may visit my tips http://www.fixya.com/support/r7833671-change_defective_motor_portable_dvd for more info.
Hint : 50% of my
repaired unit the above parts are commonly caused of the problem.
If you confirmed that you have a defective motor
then replace it with a new one. Before replacing the new motor you have to
check the clearance of the disc holder with the old one. The clearance should
be the same as the old because if not the lens will not read the disc if it is
too far or too close.
Ifyou already cleaned the lens, and confirmed that
the ribbon is good as well as the motor then I've advice you to send it to
repair shop because the next step should be done with an expert because it is
quite technical diagnosing the fault between the pick-up lens and the main
board.
Hope I helped you.
Have a nice day!
Thanks for using Fixya.
Watching a movies screen black
Can you see the menu on the display? If so, then your DVD is not compatible with the system (ex. system NTSC and DVD is PAL or SECAM). If you don't see anything at all then the display is broken (inverter is down or some diode responsable with the power circuit of diplay).
Spins CD says loading for about a minute then
first of all check for the dirt or dust on the optical unit lens, secondly check for the breakage in the ribbon type connector, which connects the optical pickup unit to the main board, if broken replace it and if still the problem persists then replace the optical pickup unit
When the dvd is loading
The laser needs replacing. You can find a disassembly guide in google if you're game. It's fairly easy, but important to be gentle with internal cables. The laser replacement should be on ebay or such. Make sure it's the right model number. any questions, email.
I purchased a DYNEX DX-BPDVD7
No disk message means that the reading sensor from the laser head doesn't get a return signal with a level high enough to trigger it. This can be caused by only 2 things - either thr return signal is blocked by dust that has settled on the laser lens and sensor, or the laser emitting diode from the head has stopped working.
The only thing you can do is to clean the laser head thoroughly: the space between the lens and the sensor with a can of compressed air and the top of the lens with a fine q-tip - be gentle the suspension of the lens is very fragile.
If even after cleaning the disk is not recognized then the player is dead - there are no parts (especially the laser head) available for it.
No disc error
mine was doing the same thing and i read some where online that if u clean the eye/lens that might take care of it. which i did. i took the chance and got a Q-tip put a little alcohol - not dripping but pretty wet and clean the lens then blow on it to make sure it is dry. then tried it and it worked perfect.
Dvd player says no disc when there is a disc in
Hi
Please check weather you have inserted the disc ,whose format is supported by your KOSS player.
If the formatt is not been supported /regonised by the player,It shows as NO DISC only.
check with some other disc which you previously played.If it plays the disc which you using has the problem.
Thanx
DVD disk will not load.
Ive had one of these devices before..
This error can be caused by one of three problems..
the disk is dirty or damaged..
The disk is a different region code then the player can play..
The lens or the interior of the player is dirty..
The only solutions are to either use a disk cleaner on the disk you are trying to play,
or use a lens cleaner on the dvd player itself after blowing it out with a can of compressed air.
The lens cleaning disks can usually be purchased at walmart or other large chain stores that have electronics sections.
WE need a AC adapter
Tries websites like Ebay.com,Amazon.com to buy any portable DVD players acessaries.
I put a password on my dynex portable dvd player
You don't. The remote is required to make this change.
Contact Best Buy phone support and explain your problem. Ask if there is a replacement remote. The number should be here:
www.insigniaproducts.com
-or-
Take it to a Best Buy store and ask a Blue shirt in the portable DVD department if they have a Dynex remote for the model you have. If they do, you can use the remote to unlock your player and be able to use it. They won't be able to sell/give you the remote, but they should be able to assist you.
Hope this helps!
Not finding what you are looking for?