20 Most Recent Frigidaire FEF352 Electric Kitchen Range - Page 4 Questions & Answers

Hi,


Check out this tip that I wrote about this problem...

http://www.fixya.com/support/r4511800-oven_problems_electric_oven_heating

heatman101

you may need to replace the main electronic control board or it is also called the clock timer.
check the continuity on the bake and broil elements. then you need to check the main power suppl to the range and make sure that the terminal block is in good working order.

this is usually a control board failure.
if the broiler and bake element.have continuity then replace the control board.if there is no continuity the replace the elements.
your problem lies in the control board.also make sure the power supplied is correct

it is not neccessary to take out the racks when cleaning the oven

a few problems can exhist with this problem: no power to unit,high limit open or defective,control defective,temp probe defective, heating element defective or burnt, and damaged or loose wire do to heat. You need a multimeter to test all these components in order to diagnose. If your familiar with electronic fundamentals I could walk you through the process.

Hello there:
The dreaded f-1 error code is not a friendly error code what it means is that the
F1 EOC (Electronic Oven Control) failure Replace Basically wht this is telling you is that the electronic controle board is bad and needs to be replaced ok
So i would get in touch with you nearest appliance dealer or repair center and if you have a warranty i would use it.
but if not get a quote on how much it will cost to have it replaced or see if you can do the job yourself and save that money ok?
Hope htis is very helpful for you
Best regards Michael

Hi


Thanks for using FixYa. F3 error means Open oven temperature sensor or thermal fuse. You’ll need to check for open wire connection between EOC (Electronic Oven Control - Clock) and the oven temperature sensor. Replace sensor if wiring is not a problem.



Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Unfortunately this usually means the Clock/Timer assembly needs to replaced. The Clock/Timer controls all the features of the oven, while the surface burners are controlled by each individual infinite switch on the control panel. Thats why your surface burners will still work, but the oven does not. That fact that there is no display also is a symptom the board is defective. They boards do not have a fuse and are not servicebale. It needs to be replaced. This is not a difficult repair and can easily be repalced by the average do-it-yoursefler. The following link epxlains how:

http://www.fixya.com/support/r3727366-replacing_control_kitchen_range

The part number for a replacement circuit board is 316207522. The overlay (the plastic preprinted template that is applied to the board) is sold separately (part number 316220804). If the current overlay is still in good shape, it can be peeled off and reused.

You can purchase replacement parts at any of the following websites:

searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

All these sites are reputable and offer great service with competitive pricing. So, shop and compare.

NOTE: The Sears website sells a refurbished version of the control board for much less than the other sites. The part number is 316207502R.

If you have any questions about this repair, please let me know. I hope this helps you.

check electrical panel of your house and make sure both breakers are in the on possition ..

Your thermostat(probe) is faulty.
CLICK HERE to see/order the part.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

HI. this is a oven temp sensor failure notice. you will need to check the wires leading from the temp sensor to the control. if the wires are in good condition and , the sensor harness is not welded, replace the temp sensor asap.

REPLACE ELEAMENTS

Hello JJ, Try pressing the "Clear/OFF" button to stop the self cleaning cycle. It will take up to an hour before the oven will unlock the door, if the oven has started to heat up for the cleaning process

You may have started the default 3 hour self-clean cycle, so you can attempt to reduce the time to 2 hours, by pushing the timer down so it displays "2" which would indicate the shorter cleaning cycle. Then at the end of the timed cleaning cycle, it should open up, once the temperature has cooled sufficiently for it to be safe to open, again, which takes up to an hour to sufficiently cool.

Typically, when an oven is accidently put into self clean mode, the timer "kicks in" and the timer has to run out before the oven will unlock. With the older mechanical knob timers, you could just rotater the timer until you reached the end of the pre-set time. With the electronic timers, you have to let the timer "count down" until it reaches zero before the oven will unlock the oven door.

Here's a link to the Frigidare site where you can select your specific FEF352 version and download a owners manual, free of charge.

http://www.frigidaire.com/manuals

Just enter in FEF352 and then scroll down the page until you find your particular version of teh FEF352 oven/range and then click on "complete owners guide" (english) to get the manual in an Adobe pdf format.

I hope you find this Very Helpful and best regards!

You just need to replace this switch which is very easy to do. Frigidaire is a wonderful brand! We have parts for all major brand so contact us at:

http://www.fixya.com/repair/d499389-accurate_appliance_repair_service from 7 AM until 9 PM CST for all your appliance parts supplies.
We ship overnight so you can get back to cooking again soon.
Thanks, Ella

The F90 error indicates Maximum oven door unlock time exceeded.


1. Check the wiring between EOC & Lock Motor Micro Switch.
2. Replace the Motor Door Latch assembly if necessary.
3. Check for binding of the Latch Cam, Lock Motor Rod & Lock Motor Cam.
4. Check to see if Lock Motor Coil is open. If open, replace Lock Motor Assembly.
5. Lock Motor continuously runs - if Micro Switch is open, replace Lock Motor Assembly.
Switch.
6. If all situations above do not solve problem, replace EOC.

TRY http://www.applianceaid.com/fault_codes.html

3-5 HRS

Yes,take the door off the range. There are screws on the bottom and top that must be removed. Open the door about 3 inches,grip it with both hands and pull up. It should come off the hinges.

it can be repaired please call the engineer

just set it to clean then it will lock the oven and let it get really hot it will loosen the spilled food by burning it off and just wiping it off when the oven cools