Zebra 203DPI Printer - Answered Questions & Fixed issues
My zm400 keeps reverting back to direct thermal
did it stay on direct thermal if you not doing any print job ?
then i assume you the problem is when you printing .In ZEBRA DESIGNER, there's a printing preference that can be set up... i think u selected direct thermal when you print with zebra designer, that's why whenever u start printing, it show RIBBON IN again.
the solution is, Just changed the printing method from zebra designer.
if you aren't using zebra designer, then the problem at your driver. Open Printer & Faxes, then right click your Printer and klik on Printing Preferenced. There u can set up the printing method to Thermal Transfer.
The thing is....... changing the Setting from LCD panel won't change the setting on the driver.
i hope this will help you
6/25/2014 7:42:26 AM •
Zebra 203DPI...
•
Answered
on Jun 25, 2014
•
7,222 views
How do I change the IP address on my zebra zm400.
Press on setup button
Press on the - button
until you see protocol
Press on select and
choose permanent and save
Press on the + button
until see the IP Address
Press on select and use
the + button to change numbers and Press the - button to move to the next
number.
Press selects to save
restart the printer by switching the printer on and off.
Test a print job to the
Printer.
4/25/2012 5:56:14 PM •
Zebra 203DPI...
•
Answered
on Apr 25, 2012
•
12,003 views
Why the IP address cannot
I have the same problem before, but i change the IP through Zebranet view tools.You can install the zebranet view from the CD provided
to your workstation and change the configuration according to the
requirement with the zebranet view
9/7/2011 12:36:05 PM •
Zebra 203DPI...
•
Answered
on Sep 07, 2011
•
1,198 views
I've got some problems with
The default setting is thermal transfer for this printer. You can change the setting on the printer so it doesn't show you the error any more by doing the following:
Press SETUP/EXIT Press Plus (+) to scroll through the different parameters About the 6th parameter is "PRINT METHOD" Press "SELECT" to select the parameter Press Plus (+) or Minus (-) to change to Direct Thermal (no ribbon) Press "NEXT/SAVE" to save your changes
If you make the changes to you printer and as soon as it prints it reverts back to thermal transfer, then your label software or your driver are overriding it and you need to make the change there.
Changing the setting in your label software - this will also change the settings for this label only
Open your label
Make the change under "label setup" or "page setup" inside your label software.
Changing the setting on the driver - this will also change the default settings for all future labels that you create
Go to control panel and devices and printers. Locate the driver for your label printer and make the change under "Printing Preferences".
8/30/2011 6:05:44 PM •
Zebra 203DPI...
•
Answered
on Aug 30, 2011
•
548 views
Power light lit
Pause light
Press the pause button to take the printer off pause...
The data light is flashing because it has labels to print...
Check to be sure your ribbon is loaded properly.
6/21/2011 5:30:18 PM •
Zebra 203DPI...
•
Answered
on Jun 21, 2011
•
932 views
For ZM400 and S4M, Has anyone had any luck with
You can try this: on the S4M, you can press the Menu key to go into setup mode. Under password level 3 parameters,there is a setting for ribbon which by default is set to Yes thermal trans. If you set it to No for direct thermal mode, this will in effect turn off the ribbon sensor. The printer won't stop now if it runs out of ribbon but usually you are there when printing to see that the ribbon is running out.
On other Zebras, you can turn down the sensitivity of the RIBBON LED sensor but the S4M doesn't have that setting.
See if that helps.
6/21/2011 1:48:27 AM •
Zebra 203DPI...
•
Answered
on Jun 21, 2011
•
830 views
Zebra wont print
Check your paper roll inserted properly and in correct way or your check
thermal head working properly
12/26/2010 9:40:15 AM •
Zebra 203DPI...
•
Answered
on Dec 26, 2010
•
233 views
Zm400 print a part of a label.
Hello, my Zebra
What part, rigth site or bottom site?
check the lengt and the with from the driver and print the testpage (have to print on full label)
if is one of the sides, try to give more pressure to that side on the printhead.
11/25/2010 11:36:42 AM •
Zebra 203DPI...
•
Answered
on Nov 25, 2010
•
740 views
I have a zebra 2844
you be able to see the net configuration wen connect first to a network, first plug-in to one network, then if you go through the settings, you be able to see IP, NETMASK and GATEWAY and change.
Thanks.
11/25/2010 10:34:16 AM •
Zebra 203DPI...
•
Answered
on Nov 25, 2010
•
335 views
Como cambiar ip de zebra zm400 desde el panel
you need to connect with some network to the ip adress coming on the setings, if you dont connect with network, that function not apper.
If connect, you be aple to change to IP estactic and the Gateway and the subnet mask.
Dont forget to save.
11/13/2010 3:16:09 AM •
Zebra 203DPI...
•
Answered
on Nov 13, 2010
•
1,462 views
Hi, My name is Hakan and I'm having trouble
If you are using a colored ribbon it might be too transparent for the ribbon sensor to read. Re-calibrate the ribbon sensor.
If you're using black ribbon and you're sure that it's loaded properly and the sensor isn't being blocked, then print a sensor profile and re-calibrate the sensors if necessary.
3/9/2010 6:02:09 PM •
Zebra 203DPI...
•
Answered
on Mar 09, 2010
•
539 views
Zebra zm400
connect the printer to a desktop or laptop using LPT1.
10/6/2009 8:28:21 PM •
Zebra 203DPI...
•
Answered
on Oct 06, 2009
•
1,634 views
ZM400 printer
Try going through the LCD menu and if it say "Direct Thermal" change it to "Thermal Transfer", Direct Thermal made means, no ribbon required, but it sounds like you do have ribbon in the printer, if so, try my recommendation. If it asks for a password, it's '1234'.
3/10/2010 9:55:07 AM •
Zebra 203DPI...
•
Answered
on Mar 10, 2010
•
3,643 views
Some noise comes when printing
Here is the link for the Service Manual required which i uploaded for you... hope this resolves your issue...
http://www.adrive.com/home/downloadfile/136030403
2/12/2009 11:04:11 AM •
Zebra 203DPI...
•
Answered
on Feb 12, 2009
•
534 views
Not finding what you are looking for?