Top 20 LG 32LC7D Television Questions & Answers

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electro-medical.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary. Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Try looking for the remote sensor. It should look a little like a camera lens or little red tinted window. If you cannot find it just give the entire front of the TV a good cleaning. Finger prints and dust build up can interfere with the signals. Do the same for your direct TV box.

Televisions now are equipped with a diagnostic circuit that send a low voltage , low frequency signal throughout your set when you turn it on. This is to detect any problems with the circuitry and protect the good circuits.. It started out with a component that wasn't working properly but finally returned the signal. With continued use the component finally burnt out and now your set is going into standby mode. The blinking Green light is a code X amounts = a certain problem. Look up the make and model on the internet and it will give what 2 blinks, three blinks, etc means.. It could be anywhere in the set but the blinks will pin point to the board more than likely. Probably in your power board and if you are lucky it is just capacitors which you can replace yourself if you are a DIY 'er. Check out their web site and find out what your problem is first. Good luck! Col. Dana Gillespie ''

D a reset to this set, and check. If it do not help you, the main system control memory IC to this set is faulty, and should he replaced. Contact any service technician. There are two types of reset to TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight; will be better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Sounds like the main system control memory IC to this device is faulty. It does not store the programs. Contact any service technician to replace it. Electro help

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ In some models of LCD TVS; the backlight inverter and its T'Con board will be a part of the panel itself, and will be a built-in type inside the LCD panel. If so, they can't be replaced. In this case; a panel replacement is the only repair. For some other models, the backlight inverter section circuit will be a part of the main power supply regulator [SMPS]. To such sets, the power supply section circuit too should be troubles hooted. Contact any service technician. The circuit will differ with models and versions. Type in the brand name of your device, in the search box [at the top right] of the display window and the Search will start at once as you type in, and will show you all the related posts. It will make surf easy.

Try another HDMI source (borrow a friend's BluRay for example} to confirm it is the TV at fault. If it still doesn't work, the TV needs a main board replacement because all the HDMI circuitry is on the main board. this usually happens after a power surge or lightning storm, and a near hit is all it takes, Sometimes, if you have a Satellite Receiver it too might be damaged on its HDMI output. So 1st try another source..IF you replace it yourself be sure to find the right board by using the TV's service # example 32LC7D-XX.XXXXXXX.. The letters where I have Xs are very important and must be matched,

Is the on time function on? Go to the menu go down to time then across to on time if its on turn it off.

Change the batteries

If TV works well, you can do it by entering its menu settings. Refer its user manual for details. If the set is not switching ON from standby, the main board to it should be troubleshooted. Contact any service technician. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

If other inputs show no problems and you are not using a cable box or satellite receiver, etc. just off air antenna, something on the main board is failing. please double check other inputs again.

To do a factory reset, you have to enter its service mode option. If you wish to get more details, check the site linked here. Surf the site in "MOSAIC" view. It will make surf easy. http://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given in detail.

main board replacement, tuners only are usally not available

yes replace the button board as it sounds as though you may have a button sticking or it may have a short. you can remove board and buy a can of compressed air and blow it off to remove all dust/dirt to see if that may help. if that does not workk next sokution would be to replace it, here is a link to ebay part. hope this helps. http://www.ebay.com/itm/like/360768561056?lpid=82 merry christmas and happy new year.

Check the wiring to the other speaker and make sure it's connected
Using a multimeter set on ohms check the resistance on the speKer that is not working and compare it to the one that does work
If it's the same then it's not the speaker but the supply to it that is faulty

why

the sound board has gone weak so would check the capacitors for a weakness they will probably be blue type as they re used most for sound boards change them for black or green type 105c type not 85c.

Check and replace the main system control memory IC. It is faulty.

Sounds like some loose connection with its wires connects between T'Con board and panel. Re-seat them once and check. If you wish to get more details, check this link.