Panasonic KX-TG1033S Cordless Phone - Answered Questions & Fixed issues

I have a KX-TG7644. Had to look harder for the Call Block directory. The manual really didn't help much. Press "Menu", go down to "Initial Settings", go to "Call Block". You can access the list and delete all or part to open up memory space. I had to do this after all the election calls.

You can turn the volume up using arrow up key on your Panasonic phone. To do this you must be on the phone. While in conversation using the phone, push arrow up key several times to increase the volume form the phone. It will not work if the phone is not in use.

The situation is that a KX-TGA931T reads out "No link to base. Reconnect AC adapter". This is what I saw on one of the used handsets I recently acquired.Unplugging and replugging either AC adapter (base or peripheral) does nothing. But the other otherwise identical handset that recently arrived evidently had different firmware, which more helpfully read out (I may be paraphrasing) "Press Locator button base for 4 seconds, then press OK." This instruction may need just a little elaboration. On the base, the lower right silver button is labeled LOCATOR INTERCOM. On the handset the upper right rubber button may have "OK" on the LCD screen above it, so when it does, it is the OK button. First make sure the base is plugged in and that you have at least a little charge in the handset. Then press that LOCATOR button (for about 4 seconds) until it beeps. It will begin to beep periodically for several cycles. While it is in this beeping mode, press and hold that OK button until it beeps. If you let go too soon, the screen reads "Error!" so just try it again, and wait for the beep. After the beep the screen reads (I may be paraphrasing) "Registering handset." This takes a few seconds. Then it is registered and when you press TALK you'll get a dial tone. Now you don't have to pay $5 for a chat with Panasonic or have to download a manual's PDF (if they even have it) and have your internet search switched to Yahoo. I do not know how many handsets this base will take - now I have 6 registered to it.

I am sure that is a service related issue and no the phone itself.

Try switching batteries with one of your other handsets known to be in good working order or replace the batteries in the handset with the problem with new ones

take a volt meter and check the contacts the phone sits on in the base station, there should be around 5 volts DC there, if there is I would replace the batteries in the phone, if there is no voltage at the charging contacts in the base then the base station is defective, another quick way to determine the cause of the problem is take the phone out of the base station and put it into one of the other phones chargers, then if the phone does charge up the base station charger is defective, u will need to replace the phone or not use the base station for charging. these are not repaired except under factory warranty.

I looked up that model and they are equipped with intercom service.
What good would an intercom function (I ask myself) without some way to ring another handset? It wouldn't make sense to have to holler for someone else to pick a handset ;-)

The phone's control layout is identical to ours (it is 2.4 gHz instead) so check the lower right-hand corner for a button perhaps marked Hold & below it 'Intercom' printed.
Using that function, you choose the station # and it will ring the remote (lost) handset until someone picks it up and presses Talk or speakerphone button. .

2013 Models How to Adjust the Handset Ringer volume on Panasonic Cordless...

If this is on all extensions then there is a problem with the transmitter in the phones base station. The lowest cost repair for this is to just buy a new phone.

Did you pay your bill??? (Just kidding) Have you checked your lines with another phone?

Is base plugged in? If no, plug it in, you have to have power to base to get it working. If it's plugged in, holster the handset in base to "reset" the handset.

sorry, it seems that they have no manual for this model online yet. however, the procedure to reset handsets might work if you go to page 35 of the manual ("http://service.us.panasonic.com/OPERMANPDF/KXTG1032.pdf") good luck!

1. [MENU] 2. Use up/down {V}/{^}: "Answering device" --> {OK} 3. Use up/down {V}/{^}: "Settings" --> {OK} 4. Use up/down {V}/{^}: "Ring count" --> {OK} 5. Use up/down {V}/{^}: Select the desired setting. 6. {OK} --> {OFF}

If it is a landline phone, it may be receiving interference from other electrical devices in your home. Try moving the phone to another wall jack, or if using a router , remove router and go straight to wall jack. If problem persists, call your service provider's customer service.

Manual available at manufacturer web site.

NO LIN TO BASE MOVE CLOSER TO BASE, TRY AGAIN

GO TO PLAY STORE THEN TYPE IN VOICE MAILK THEN IT WILL BE A LOT OF STUFF THAT POPS UP

Press off 2 times

First make sure it isn't on mute. Then get all of your contact information and pictures,etc before resetting your phone. If these things don't work you most likely have a bad microphone.

The broadcast channel can't be changed according to the units instructions some other electronic device is causing the interference you may have to move the base unit. A PDF file of instructions are here http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=2&ved=0CCgQFjAB&url=http%3A%2F%2Fservice.us.panasonic.com%2FOPERMANPDF%2FKXTG1032.pdf&ei=Jl_aVNSkGobAggTGlYHoBg&usg=AFQjCNEKuKWxZUBDTtUXNDQOW8Mn92B2dw&sig2=oBfK0fI1HOBEHWvabQGLpA