Audiovox D1917 - Answered Questions & Fixed issues

I cleaned the lens, but I also tip the play upside down with the disc in it and it seems to work.

The only thing you can try is clean the laser lens with rubbing alcohol and a Q-Tip, allow several minutes to dry before testing, If this fails the laser pickup assembly will need to be replaced, a costly adventure.

Tries websites like Partstore.com,Amazon.com,Ebay.com to buy.

First you should do the basic, try to use a cd cleaner if still same problem try to use a cotton buds to wipe it but be sure not to touch the lens. If still no changes your optical lens must be adjust, remove the optical lens you will see a potentiometer under the optical lens try to adjust it,but very slight adjustment is needed the try to test your unit. Hope that this may help.

I'm using klite codec and it's not giving me any problem watching any video formats. You can download it on this website: http://www.filehippo.com/download_klite_codec_pack/

Hello, please get the code here : www.regionfreedvd.net/ www.dvdripper.org/dvd-region-codes-vs-ntscpal/ www.regionfreedvd.net/players.html
www.dvdreviewer.co.uk/Forums/...region_code/page1
Best Regards, Jay_cd56

get a dvd cleaner disk. it realigns the laser and cleans the laser lens. clean the dvd compartment with a dry cloth

The error means that the player doesn't recognize the disc. This can be caused dirt on the lens or the optical drive lens not tracking properly (It isn't looking where the data was burned on the disc.) Problems with the disc can also cause the issue (disc not finalized, scratched, etc).

Try a lens cleaner and a different dvd. Otherwise, it probably isn't worth fixing, imo.

I wish that I could be of more help.

Cindy Wells

Hi DO NOT LOOK INTO THE RED EYE this is a lazer beam & the unit is not working safely if it is doing this & if it is the portable type dvd 7inch etc it is better to get a new one as the part are more than the cost of a new one .

you need to clean the disc and make sure it fits in wright if that dose not work try another disc.

This of course may not be the exact same thing, but mine did the same thing. Sounding like it was loading, but in fact pressing the open button it I could see the disc not spining at all (normally you would.) With the power off of course. I took all the bottom screws out (where ever the arrow points to a screw) including to the display. There is one ribbon cable easily disconnected. I lifted the mount the DVD sits on and reseated it. I put a disc in it, turned on the power and the disc turned. Great I thought. I reconnect the cable, put the screws back in - and its working.

Sorry to say, he ruined it. No way to fix. Live and learn.

Hello kclark723,

If it's not the cord itself its the female plug in on the main board of the dvd player. There is little you can do about this as it is soldered onto the board and can not be replaced except by an experienced electronics repair technician.

The cost of having such a thing done would be nearly as much as buying a new one. If it is still under warranty then you can send it in to the manufacture to have it repaired or replaced. If not then you will have to decide upon having it repaired (portable dvd players are meant to be thrown away when suffering from such damage) or you can buy a new one.

Sorry about your misfortune, and thank you for trying Fixya!

Set the A/V output to IN

It's possible that the issue with your Audiovox pursuit PRO9056c remote start system is related to the antenna or its connection. Here are a few things you can try to troubleshoot the issue:

1. Check the antenna connection: Make sure the antenna is properly connected to the control module of the remote start system. You may need to remove the panel where the antenna is mounted to access the wiring and connections. Check the wiring for any signs of damage or corrosion, and make sure the connections are tight.
2. Check the fuse: The remote start system may have a fuse that is responsible for powering the antenna. Check the fuse to make sure it is not blown or damaged.
3. Reset the system: Try resetting the remote start system by disconnecting the battery for a few minutes, then reconnecting it. This may help reset the system and resolve any issues that were causing it to malfunction.
4. Consult a professional: If you are not familiar with automotive electronics or are unable to resolve the issue with the above steps, it may be best to consult with a professional technician who can diagnose and repair the system for you.

It's also possible that there is a problem with the remote start system itself, such as a malfunctioning control module

See if the videos and articles help. https://www.google.com/search?q=connect+a+Roku+2+to+an+Audiovox+ADV12 ..

Unfortunately, you are probably dealing with a copy protection issue. The digital handshake can't be returned by your KLV3913. You get the same issue if you connect a HDMI source (Blu-ray player) to a VGA monitor. I wish that I had better news for you. Cindy Wells

It's all one board, chances are your audio output IC has failed and needs replacing

Jim, First thing I would do is try a different DVD to see if the problem persists. Otherwise, this device is equipped with integrated speakers, meaning it is unlikely that you will be able to replace them. You may be in the market for a new Audiovox, unfortunately; but before you scrap it I suggest taking it to a local electronic repair store near you. Hope this helps, Best regards

I I had a similar problem. What worked for me, was resetting the player. By pressing the picture button on the player itself three or four times I got to the reset option. Press play when it says press ok to reset. My remote automatically started working at that point. Hope this works for you