Philips Magnavox MWR10D6 DVD Recorder - Answered Questions & Fixed issues
I get an error code E454037380
How to solve the error whirlpool cassette, the error is Error is E 45 which is written is imp board , I need feed back as soon as good. Thank you...
No power at all on my magnavox mwr10D6
Brown outs can damage the power control board of a running product. It's likely that while the other devices that all were affected by the brown out made it through such a condition, your DVR probably did not. The good news is, there is typically a fuse that can be changed which may have blown. If you open the unit up, check the fuse first. If it looks okay, there is a set of capacitors (looks like tiny round cans, usually blue or black) If there is what looks like a weird papery appearance around the can(s), or the top of the cans are bulged or cracked, the capacitor(s) need to be replaced.
Trying to connect Magnavox MWR 10D6 DVD/Recorder to Sanyo HDTV. TV is connected to Dish network through coax. cable.
Unfortunately, the Magnavox MWR10D6 recorder can not record HD signals. It's only video inputs are coax (RF) and composite video; both are limited to 480i (SD). NTSC (analog signals) are translated to video. Your best recording option is to connect the composite video output of the Dish receiver to the video input (yellow for video, red and white for audio) of the recorder. Then set the receiver to the channel that you want to record and set the recorder to Line In. HD recorders may exist. They are much more expensive than the SD versions. I wish that I had better news for you. The manual for the MWR10D6 is available from Funai here:
http://www.funai-corp.com/support/om/MWR10D6.pdf . Cindy Wells
Recording error
mine was doing the same thing.and we found out that if you recorded something and dont finalize it will not recored anything else till you finalize what you recored then it works again
I have a magnavox zc320mw8
Thank you for this solution! I have been struggling with this same problem for days and this fixed worked. I am so grateful.
I think i might need a firmware update.where can i
This depends on what you are trying to update. But usually you download updates from the website of your product and once there is an upddate directions to go about it would be added to it.Hope this solution has been helpful?
Cannot set anything with the
Tries to clean out the batteries compartment like metal - + battery connections with a rag with some WD40 chemical to get rid of the rust and dries condent moisture.Wait like another 10-15 mins for the effect to take place,replace the remote with a new set of battery,it should be working again.If it still have the same problems,the remote control CPU chip it is dead,the remotes devices it is heavily dependent on it CPU chip.Try website like Remotes.com to buy another remote same as the original or very close compatible to the original remote.
I can't record a DVD
You need to select front AV as you video source on the DVD recorder if using the front AV phono connectors. Make sure the lead you use from the VCR is working y connecting the AV leads directly to your TV if possible.
We have a Wii that plays through a Magnavox
Assuming that you plugged the video cable from the Wii into the "VIDEO IN" connections on the Magnavox, you need to do two things:
1) go into SETUP and make sure the inputs are set to regular/composite, NOT S-Video
2) use channel -/+ on the Maxnavox remote to select the correct input
Trying to record from a
Connect scart VCR to scart DVD (full scart lead) or RCA (phono) video out yellow VCR to video in DVD and audio outVCR white/red to audio in. Select the correct input or source to the DVD recorder and off you go.....
I hope I have been of help but please do not hesitate to ask if you have any further questions.
I appreciate your vote if you appreciate my reply and remember, even if you don't vote for me a please and thank you goes a long way.
Not finding what you are looking for?