20 Most Recent
Yamaha RX-V673 7.2 Channel AV Receiver BONUS PAK w/ Two HDMI Cables - Page 4 Questions & Answers
What does error code 0010 mean on Yamaha av receiver Rx-v773
- Firmware update doesn't start or doesn't complete
? Receiver doesn't power up after the update.
? Error message appeared when confirming the firmware version.
Recovery method using USB method:
1. Unplug the AC power cable from wall outlet.
2. Insert the USB thumb drive which has the firmware data stored inside, into the USB port located on the front panel.
3. Press and hold the INFO key and keep it pressed while you plug the AC power cable back into the wall outlet again.
" USB UPDATE " will appear on the front display. Then, release the INFO key.
4. The update will start automatically.
5. When " UPDATE SUCCESS " appears on the display, firmware update is completed.
Power off the receiver and remove the USB thumb drive.
6. Confirm updated firmware version.
- Error message appeared during the update
Cause: For some reason, the receiver can't read the firmware data.
Method: For your solution, check the following
[Update through Internet]
? Check Internet connection.
Check if the Internet connection is working by playing an Internet radio station.
(See owner's manual for details)
[Update by USB thumb drive]
? USB thumb drive is connected properly to the receiver.
? USB thumb drive is not password protected.
(AV receiver cannot read data from a security protected USB thumb drive)
? Make sure the USB thumb drive is inserted before the receiver is powered on for the update.
? The firmware data is stored in the root directory of the USB thumb drive.
? There is no other data except the firmware data in the USB thumb drive.
? No folders are created in the USB thumb drive.
Else, retry the update by USB using another USB thumb drive.
How many glass fuses in a yamaha av receiver HTR 6030
AVR
USA or not USA.? countries have laws on power.
Our manual 6030 shows not one fuse on the outside at all
so they are some inside (fuses) glass or not glass does not mater
what matter is blow fuses off all kinds, and present inside.
if it is dead the AVR is it. not told
i read your service manual, and there are 2 fuses.
10amp 125v , USA spec AVR
Yamaha Amplifier AS 301, AS 501 intermittently shut off
2021 amp, has new TRICKS , add STANDBY.4 causes,(more really) in the manual 1: speaker wire shorts or even speaker.2: overheating of final PA power amp out. vents blocked. or lint.3: a bad amp,(inside)run the amp, on desk not a cabinet and cool 20F room,no cables connected by AC power. 4: so does same thing at 8 hours unused it goes to STAND BY MODE. (2021 amp, now do this trick (wow)does it still fail, this 1 test. do tell.I have 40 year old amps here 100watt RMS out.that self shut off for speaker short or too hot.nothing at all new about that and do not need a processor to do that ever.(facts)!what matters are the new 2021 tricks inside.it does say turn the volume down to stop amp overheating. or let it cool in the manualor power surgedor Impedance switch set wrongthe Power LED dims so show standby
HTR-3065 Firmware Update
Through an authorised Yamaha Electronics Service Centre.
They are not available to the public as firmware damage may occur and that will destroy your receiver.
Yamaha Rx-V371 will not turn on
It's in protection mode. Disconnect all speakers and hold the Tone and Straight buttons while hitting the power button. Hold all buttons down for 3 to 5 seconds. This will turn off protection mode. Now power down then back on. If you haven't damaged anything it should work fine. Make sure all speaker connections are good. Always power down the unit before making any speaker or other connections.
Yamaha RX-v685 - Surround Sound Issues
If you are in Pro Logic mode and play a stereo recording/film etc, there will be no rear sound.
You need a Pro Logic recording to produce true rear sound.
Yamaha CX-A 5200 protection circuitry has been activated - won't power on
I would get it fixed at a Yamaha Service Centre, as you don't have the test equipment to find which failed component is causing it to shut down and protect itself.
The only thing you might try is looking for bulging or split capacitors. That WOULD cause circuit protection, because they are power stores and smoothers.
Not finding what you are looking for?