Frigidaire PLEB27T9DC Electric Double Oven - Answered Questions & Fixed issues



Hi,

Seems like you found out the hard way what I wrote about in this tip...

Check it out it also contains some thing to try on how to unlock that oven..

Self Cleaning Oven Problem

heatman101

Asker

Frigidaire... | Answered on Jan 10, 2011 | 262 views


make sure oven is set for manual and not time bake if set for manual and oven does not come on check the bake element any appliance parts house can test your element

Frigidaire... | Answered on Nov 18, 2010 | 203 views


Here is some wisdom for understanding F1 fault codes.

In some models, there are subcodes that make diagnosis even easier.

Here's a simple explanation of what's going on and how to troubleshoot:

The F1 code indicates that:


a. The electronic range control (ERC) is sensing heat in the oven when in a time-of-day (i.e., not cooking) mode.

b. The ERC is receiving information to run multiple heat functions simultaneously.


Although different components (depending upon the model) could generate the code, simple and straightforward testing using your ohm meter is all you gotta do to test for it.

1. Check the oven temperature sensor. The oven sensor has to be within spec or it will cause the F1 code.
As an example of being out-of-spec, the ERC will generate an F1 fault code when the sensor shows 1650 ohms during a time-of-day mode.
This is equivalent to 350°F in the oven.
The resistance isn't high enough to generate an F2 code (runaway temp) or an F3 or F4 code (shorted/open sensor circuit).
The ERC monitors the sensor circuit after a heat cycle and expects the resistance to drop back to 1050-1100 ohms.
The fault code is generated when this doesn't happen. Checking the sensor circuit means also checking the harness,
harness connections and the sensor itself.

2. If the oven sensor circuit checks okay, then turn your inquisitive eyeballs to the touchpad.
If the range has a separate touchpad/keyboard, the keypad may have moisture that is shorting several circuits simultaneously.
If the F1 code is given immediately (instead of during or after a heat cycle),
remove the ribbon connector from the touchpad to the ERC after clearing the F1 code. If the F1 code does not return in five minutes,
then cast a suspicious gaze upon the touchpad/keyboard. Shorts may be caused by using an ammonia-based glass cleaner.
The touchpad surface will absorb ammonia-based cleaners that are sprayed directly on the glass surface. When heat is applied,
the surface material can break down causing shorts.
If you're gonna use ammonia-based cleaners on your control panel, then you should spray it on the rag and then wipe the touchpanel
-don't spray directly onto the surface of the touchpad.

3. On Amana ranges with a rotary temperature dial, be sure that the knob is in the OFF position when performing tests.

4. If these tests all check good, then replace the ERC.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
HJU&^

Frigidaire... | Answered on Oct 01, 2010 | 294 views


the usual cuase for this problem is that the element has gone, usually fairly cheap to buty and easy to fit.

Frigidaire... | Answered on Nov 28, 2009 | 100 views


wow, that is so weird...i was just getting ready to write the exact same thing. this last time mine beeped, i just kept letting it beep for several minutes. if kept on. i then went in and pressed all the buttons except for cancel and nothing happened. then i pressed the oven light button. the beeping stopped. not sure if it's coincidence or if that was what i was supposed to press. i will keep messing with the buttons and let you know if i figure it out. i will dread if it beeps all night long.

Frigidaire... | Answered on Feb 14, 2009 | 774 views


Turn the power off at the breaker box for five minutes.
this will reset the system of any electronic glitches.

Thank You For trusting us with your question
Please remember to leave a solved rating before you leave!

Frigidaire... | Answered on Jan 01, 2009 | 265 views


This exploded diagram of the door should help you get it apart, 4eb927f.gif It is going to be shrunk by the forum software, the full size image is
here http://www.easyapplianceparts.com/AdvancedModelSearch.aspx?ModelNum=FEB30T6DCC&mfgModelNum=&fkMfgID=4
along with a full list of parts should you need them

Frigidaire... | Answered on Nov 07, 2013 | 321 views


I would use a number 6. always better to use more then you need.

Frigidaire... | Answered on Aug 08, 2008 | 89 views


stick with GE EASY TO SOURCE PARTS

Frigidaire... | Answered on Jun 16, 2008 | 89 views


you will need a top oven thermostat

Frigidaire... | Answered on Jun 16, 2008 | 302 views


there is sometimes a thermal fuse inside the caseing might have to take the top off if not then you will need a new timer be safe and unplug

Frigidaire... | Answered on Dec 23, 2008 | 2,481 views


there should be some screw holes along the sides installation instructions should have come with the unit but if they did not can get them here http://www.frigidaire.com/support/ResultsPage.asp?strModel=PLEB27T9DC&User=&Search=Search

Frigidaire... | Answered on Feb 13, 2008 | 482 views


nextwave, looks like you have a safety thermostat (TCO) on the back of the oven. Should have a red and red/white stripe wire going to it. If this opens it will cut the power to the display, part number is 316003606. The hardest part of this gig is pulling the oven out to change the t-stat out. Catriver.

Frigidaire... | Answered on Apr 02, 2008 | 118 views


check the fuse/breaker for the bottom element

Frigidaire... | Answered on Dec 14, 2007 | 442 views


it must be thermostat in bottom oven

Frigidaire... | Answered on Oct 26, 2008 | 309 views


Try pressing and holding the Clear/Off button for 3+ seconds. The LOC indicates the control panel lock is enabled. The LOC should clear from the display. Note: if you hold the key pad for too long, the lock will reengage. From the picture of your range that you included, I believe this is the key pad button just below 7 to the right of the LCD display. There is a label in a small font just below the key pad. (The label probably is a padlock symbol and the word Controls but I can't resolve it from your picture.) Some newer Frigidaire Gallery ranges have a key pad button with a padlock symbol; this would be the correct button to press and hold on those models.

Warning: on some models, the door lock will also engage. Do not try to force the door open. Wait for 15+ seconds for the door lock mechanism to fully disengage before attempting to open the door.

I hope this helps.

Cindy Wells

Frigidaire Ovens | Answered on Jul 05, 2020 | 23 views


How to Reset a Frigidaire Oven
  1. Press and hold the "Bake" button for six seconds until "0°" appears in the display.
  2. Enter the lower temperature at which you want to reset the oven.
  3. Press "Self Clean" to reset the oven's internal temperature to a cooler setting
https://www.hunker.com/13409693/how-to-reset-a-frigidaire-oven

If your Frigidaire oven has a manual lock, slide the lock-bar to lock the oven's door. If it does not have a lock-bar, the oven will lock automatically. 3 Locate the "Clean" button on the oven's control panel. 4 Press the "Clean" button to begin the cleaning cycle.
https://www.youtube.com/watch?v=DSYUj3yGybY


Frigidaire Ovens | Answered on Apr 17, 2020 | 52 views


possible bad control board

Frigidaire Ovens | Answered on Jan 18, 2020 | 96 views


The F10 error can be caused by a faulty relay or electronic control board if the oven overheated while in use. If you unplug the range and the error occurs when the range is cool, then the over-temperature sensor has failed or the electronic control board is faulty. Even the wiring between parts could be faulty.

You need to check sensor and wiring. On some models, the oven temperature sensor probe can be accessed by opening the oven door. Look for two screws that are close together. Otherwise it's accessed from the back of the oven. It may be covered by an access panel. Unplug the wiring harness and check the resistance across the sensor with a multi-meter. It should give 1100 Ohms. Similarly check the wiring resistance from the probe to the control board. Also check the relay and that wiring. Replace the wiring, sensor or relay if those are faulty. Otherwise you need to replace the control board. The control board will be behind the console access panel. Somewhere on the back of the range, there will be a trouble-shooting sheet giving the wiring diagram and the expected resistance or voltage across the parts of the range.

I may be able be able to provide a parts diagram and price list for parts on your range. Please add a comment with the model number of the range for this information.

I hope this helps.

Cindy Wells

Frigidaire Ovens | Answered on Jan 04, 2020 | 115 views

Not finding what you are looking for?
Frigidaire PLEB27T9DC Electric Double Oven Logo

Popular Tags

30 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Ovens Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Frigidaire Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...