Top 20 Frigidaire PLEB27T9DC Electric Double Oven - Page 8 Questions & Answers

Thank you for your inquiry, Stphanie Perreault!

From my understanding your Frigidaire oven will not heat up properly. It sounds like a possible issue with your thermostat or sensor. I would recommend allowing a professional technician to perform a proper diagnosis and locate the part needed for repair. This will help to avoid any unnecessary part purchases. Good luck. -Matt

I appreciate your inquiry, Stephanie Givan!

From what you are describing it sounds like a possible short with your breaker box or issue with your terminal block within your Frigidaire range. I would recommend reaching out to a professional technician for a proper diagnosis to be completed. The technician will have the correct tools to check for any electrical issues within the range to make sure the correct component is being replaced. This will help avoid any unnecessary part purchases. -Matt

Thank you for your inquiry, Bego?a Rebolledo-Kaufman!

From the information you have provided you are experiencing an issue with your Frigidaire double oven not heating. It sounds like a possible problem with your element or thermostat. I would suggest to perform a reset on your range, to see if that would help correct any miscommunication within the electrical components. In order to reset your range you would need to flip the household circuit breaker off for ten minutes. If you still continue to have an issue with the oven I would recommend having a professional technician out to provide an accurate diagnosis and replace any electrical parts needed inside of your oven. Hopefully this is helpful to some degree. -Matt

Good Morning Marlyn Allen, thanks for your post!

Based off the information you have provided your Frigidaire oven door will not open after it has cooled down. I would hold down the clear or cancel button for ten seconds that should release the door. If that does not work I would perform a reset on your oven and you can do that by disconnecting the power from it for approximately ten minutes. You can also perform another self-cleaning cycle and before it starts cancel the self-cleaning and then wait for ten seconds and the door should release. If you follow these steps and the door does not open it could be a faulty door latch and that would need to be replaced by a technician. Best of luck! -Matt

The breaker for the over is normally in the main house fuse panel. Be very careful when working on any electrical feed for your oven, that is normally a 240v outlet.

Thank you for your post, friend!

I see that you are having some challenges with your Frigidaire range. On your control panel if you have a "Clear" or "Cancel" button you can hold that down for five to ten seconds and it should release the latch. You can also hold down the light switch button on the oven door frame and the cancel button simultaneously for five to ten seconds to see if that would correct the problem. Last, I would perform a reset on your range which can be done by disconnecting power from the range for ten minutes. I hope this has been helpful. -Matt

Hey friend, I appreciate your post!

It sounds like your Frigidaire oven could need to be calibrated. If could also be an issue with you thermostat or control panel. In order to properly calibrate your oven you would need to seek assistance from a professional. I would also recommend seeking assistance from a professional for proper diagnosis to avoid any unnecessary part purchases. I hope this information is helpful. -Matt

Hello friend, thank you for your post!

Based off the information you have provided your question is under an "F13" error code but you also stated that it is showing you an "F1" error. I have researched both error codes for you. "F13" usually indicates error identification, which could be an issue within your control board. "F1" typically can indicate that the range has detected an issue with the runaway temperature (overheating). Both codes could be corrected with a reset, which you can do by flipping the household circuit breaker for roughly ten minutes. If that does not correct the issue I would recommend contacting a professional. I hope this is helpful. -Matt

Hello friend, thanks for your post! From what you are describing it sounds like a possible issue with your control panel or door assembly. I would suggest a reset to your appliance which you can do by disconnecting the power for ten minutes, either by unplugging or flipping the household circuit breaker. Additionally, do you see a lock symbol on your control panel? If you do I would hold that button down for three to five seconds. If that does not correct the issue you are currently experiencing I would recommend seeking assistance from a professional to come and properly diagnosis your appliance. I hope this is helpful. -Matt

Good Afternoon Friend, this is Z. I am happy to assist you! I understand you are seeking a site that provides a listing of error codes on your Frigidaire oven. This information is very rare to find. Is your oven receiving an error code? If so, may I have the error code and with this information I'll be more than happy to help you narrow down the possibilities of the code. Thank you!

Good Morning Friend, that's a great question! Typically error code F10 indicates that your Frigidaire range has detected an issue with the runaway temperature (overheating). Let's attempt reprogramming your range by either unplugging it or flipping the household circuit breaker off. It is best to wait roughly ten minutes and then turn on your range. Usually this will clear most false error codes. If issue persists, at this moment I would suggest contacting a professional to proceed further. Most likely the RTD Probe (Resistance Temperature Detector) or the EOC (electronic oven control) will need replacing. Hope this helps! - Z

Hi Don, this is Z. Thank you for your post! If you are receiving error code F9, it typically indicates that the maximum oven door unlock time has exceeded. If resetting the power did not clear the error code, it would be advisable to contact an experienced appliance repair tech to assist further since your range may possibly have a communication error with the EOC (Electronic Oven Control), lock motor assembly, door light switch or door latch assembly. Hope this helps!

Hello Friend, this is Z. I am happy to assist you! If you are getting an error code F30 on your Frigidaire range, it usually indicates an issue with a faulty sensor probe or a wiring harness between the sensor probe and EOC (Electronic Oven Control). You may try and reset your range by disconnecting the power or by flipping the circuit breaker off and back on after 10 minutes. This often clears most false error code. If the error code does not clear, most likely the EOC of your range will need replacing. I am fairly confident that an authorized service agent will be able to restore your appliance to its normal operating condition. You can often locate a qualified service technician on the manufacturer website.

Hi Friend, that's a great question! I have successfully located the Owner's Guide of your Frigidaire range (GLEF379DSG) that includes before setting oven controls and setting surface controls. You will step by step instructions on how to do so on pages 6 through 9. I hope this information proves useful. If there is anything else that I can help you with, please feel free to reconnect! - Z Frigidaire Manual Search Results

Good Morning Friend, I understand that your Frigidaire oven will not heat to temperature if you set it to 350 degrees. I see that you have to set it to 450 degrees for it to heat up, and then turn it back down to the desired temperature. Please try resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power, set the clock and try setting the temperature to 350 degrees. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful. -Best Regards- WP

Good Afternoon Friend, this is Z. I appreciate your post! If you are receiving an error code F11 on your Frigidaire range, it typically indicates that your range has detected an issue with the runaway temperature (overheating). One of the best ways to determine if this is a false error code is to reset the power to the appliance by either unplugging it or flipping off the breaker for about ten minutes. If the error code persists, at this moment I would suggest connecting a professional to proceed further. Most likely the EOC (Electronic Oven Control) or RTD Probe (Resistance Temperature Detector) will need replacing. I hope this information helps to some degree.

Good Afternoon Friend, this is Z. Thank you for your post! Based on the symptoms you are describing, you may either have a communication error from the EOC (Electronic Oven Control) or faulty bake element. Let's try resetting your oven. You can do this by either unplugging it or the household circuit breaker off. It is best to wait approximately and then wait ten minutes. If resetting the power does not correct the issue, I would suggest contacting an experienced service technician to determine the precise cause. Best regards!

Hi Friend, thank you for your question! I understand you would like to know how to unlock the door of your Frigidaire oven. May I please have your model number? You can typically locate the serial tag (which lists your model number) inside the storage drawer, on the right side. With this information I can provide you the correct instructions. Thank you! - Z

Could be thermostat. Could be the seals around the oven door. Are the springs that close the door in good condition. They should hold the doorfirmly shut

Good Morning Friend, I understand the control panel is dim and hard to read, on your Frigidaire oven, model# FEB756CETF. Please try resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and set the clock. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful. -Best Regards- WP