20 Most Recent Phoenix Gold Octane-R 15.0:1 Car Audio Amplifier Questions & Answers

PG won't release schematic diagrams. Are the burned components resistors? If so, what are their circuit board designations (Rxyz)?

most likely your power wire is hitting metal or your ground wire.

You need an owners manual?

Parallel would be the best way to wire them. 2 4 ohms subs to one channel wired parallel would be a 2 ohm load for that channel and if u wire them series then 2 4ohm subs to one channel would be an 8 ohm load for that channel.

ok, connect the amp positive to the positive end of one sub coil, take the negative of that coil, and run it to the positive of the second sub coil, then run the negative out of the second sub coil to the negative of the amp.

bridge it and rear channel if you need to know how to bridge let me know

THE BASS GETS LOUDER AND LOWER.COULD BE A VOLTAGE DROP.IF YOU PLAY AT LOWER VOLUME WITH NOTHING ELSE RUNNIG,LIGHTS,AIRCONDITIONER,THOSE THIS STILL HAPPEN? THOSE YOUR FRONT HEADLIGHT BLINK WHEN AND LARGE BASS NOTE IS HIT?R U USING A CAPICITOR INLINE WITH THE BATTERY,I HIGHLY SUGGEST AMPS THEAT PULL DIRECTLY FROM BATTERY CAN CAUSE DAMAGE TO THE IC IN THE ALTERNATOR.RATING PLEASE ,GIVE MORE INFO

Question edited for clarity. Contact the maker direct for parts Kevin. https://www.google.com/search?q=Phoenix+gold+xs+3400 ..

If your Phoenix Gold iron is not heating up and all the blue lights are flashing, it indicates a potential issue with the iron. Here are some troubleshooting steps you can try: 1. Check the power supply: Ensure that the iron is properly connected to a functioning power outlet. Make sure the power cord is securely plugged in and that there are no loose connections. 2. Allow the iron to cool down: If you have been using the iron continuously for an extended period, it may have reached its temperature limit and shut off for safety reasons. Let the iron cool down for a few minutes and then try turning it on again. 3. Clean the iron's soleplate: Over time, the soleplate can accumulate dirt, residue, or fabric fibers, which can affect the iron's heating performance. Make sure the iron is unplugged and cooled down before cleaning the soleplate. Use a damp cloth or sponge to gently wipe the soleplate and remove any debris. Avoid using abrasive materials that could scratch the surface. 4. Check the water tank: If your iron has a steam function, ensure that there is sufficient water in the tank. If the water level is low, refill the tank according to the manufacturer's instructions. A low water level can prevent the iron from heating properly. 5. Perform a reset: Some irons have a reset button or a combination of buttons that can be pressed to reset the device. Consult the user manual for your specific model to find out if it has a reset function and how to perform it. 6. Contact customer support: If the above steps do not resolve the issue, it is recommended to contact the manufacturer's customer support for further assistance. They can provide specific troubleshooting steps or advise on repairs or warranty options if necessary. Always refer to the user manual provided with your Phoenix Gold iron for model-specific instructions and safety guidelines.

remove speaker wire a amp, terminals does OVL come on now.??? test 1 done report. a CAR amp. no model told at all. MX or RX xxxxxx numbers. etc??? nobody can guess what is in your hands https://phoenixgold.com/collections/amplifiers

Request the diagram from Phoenix Gold.

http://download.phoenixphorum.com/Manuals/Speakers/XS/XS104_DVC_Specs_and_Boxes.pdf here is the specs for the dvc version

Look up the part numbers on the components themselves. I can assure you that they are readily available from places not named PG. They are made in a factory with a bunch of diffenent Brands. If simply trying to repair the knob you may be able to use another knob from different Manufacturer if it takes the same jack for wire.

Probably the power is not received by the heating coil, check fuse near the power cable (inside the flap on the iron bottom), or sometimes there is fuse in the power pulg of the power chord. It is rarely that the lamp is blown