20 Most Recent Jenn-Air JGR8850 Gas Kitchen Range - Page 6 Questions & Answers

Since Jenn-Air has been acquired by Whirlpool, there have been an explosion of problems with their appliances.
Please research your intended purchase before deciding on a replacement:
Jenn-Air info
Considering the array of early failures everyone seems to be having with appliances (US made and foreign) bought in the last few years, I couldn't even recommend a manufacturer any more.

Please visit the following site that may help you out. You didn't put the model, so im hoping this will help you out.

http://www.jennair.com/assets/product/JDS9860BDS_Use%20and%20Care.pdf

If that doesn't help please visit
http://www.jennair.com/catalog/product.jsp?parentCat=2&cat=69&prod=1447&tabOption=specs#info
so you can speak to live representative. Just click live chat on top.

there is a spark module that controls all four surface burners usually located behind the rear access panel. This may have been a casulty of the outage. good luck

hi i have a Jenn air down draft as well you should have a spring loaded flap like a dryer they sell them
separately, you can buy them at home depot or lowes that will stop some of the cold air coming in not all of it.

take a 24 inch peice of coat hanger make a small u in one end and insert it from the left side gentlw fish for the door latch hook and pull it over to un latch the door and let me know if the code goes away

doubt if wares are available as a spare. just go buy some heatproof wire of the right size - should be available from any electrical shop

Dry the ignitors and see if that works. If not, then get new ignitors.

You should be able to remove the hose from the blower and lift the unit out of the countertop. Then there should be screws around the sides to take out that will give you access to the inside.

spark relay malfunction

If it is only happening with one burner, the switch on that valve needs to be replaced. If it does it with all the burners it is a problem with the spark module or control.
Post back if you have any questions.

If it's an older oven, forget about getting a new clock. Instead, have it removed (or do it yourself, mark wires and of course discontinue using oven) and try your local parts guy to see if he can send it away to have it rebiult. Best case scenario. Either that or have a technician "bypass" it for you.

F7 Function key shorted or stuck button Replace touch pad or clock assembly (also called the ERC) or attempt to un-stick button F7 Shorted key sensed for 32 seconds 1. Membrane shorted, or,
2. Display board defectiveIf touch pad is a separate unit then unplug it and see if code comes back.  Unplug range before doing so.  Once touch pad is disconnected, plug range back in and see if code shows.  Wait a few minutes.  If no code then replace touch pad.  If code does come on while touch pad is disconnected then replace main control.  If touch pad and main control are all one part then replace the whole control.  Doubt if you would have any luck trying to unstick the bad button as stated above.

  If this is a gas range your problem is most likely your oven ignitor.  As they get older they get weak and takes longer to open gas valve.  Eventually it won't come on at all.  Replacing the oven ignitor will often take care of problem.  BE SURE TO UNPLUG UNIT BEFORE REPAIR!!
  Remove oven floor.  The ignitor is in a cage attached to back of oven burner.  It mounts with 2 screws.  You may have to cut wires and wirenut in replacement.  Doesn't matter if the 2 wires are reversed.

Some are more difficult than others to get to. In some cases you will have to splice wires together. If you are not comfortable with this you should let a professional do it.

It is normal. The keyboard should works fine in stove's temp range but not in over heating conditions.

Shannbooks The first thing I would recommend to do is to reset the power. Turn off the breaker for the range for couple minutes and then turn it on. In the most cases it works. Set the time of the day and try to use the oven. If it would not solve the problem let me know. Good luck. Gendos. post back...

There are several possible reasons why your Jenn-air JGS9900 gas range may not have power:

1. Tripped Circuit Breaker: Check the circuit breaker for the range in your home's electrical panel to see if it has tripped. If it has, reset it.
2. Loose Electrical Connection: Check the power cord connection to the range to make sure it is secure. Also, check the wiring connections behind the range to ensure they are properly connected.
3. Blown Fuse: If your range has a fuse, check to see if it has blown. You may need to replace it.
4. Faulty Control Board: The control board is responsible for supplying power to the range's electronic components. If the control board is faulty, it may need to be replaced.
5. Faulty Igniter: If the burners are not igniting, the igniter may be faulty and need to be replaced.

If none of these solutions work, it may be best to contact a professional technician to diagnose and fix the issue.

There are a few potential issues that could cause the problems you're experiencing with your Jenn-Air broiler. Here are a few things you can try:

1. Make sure the gas supply to the broiler is turned on and that there are no blockages in the gas line.
2. Check the gas valve to make sure it is open and functioning properly.
3. Make sure the gas burners are clean and free of any debris or obstruction.
4. Check the broiler burner for proper ignition. It should ignite within a few seconds of turning on the broiler. If it does not, the burner orifice may be clogged and will need to be cleaned.
5. Check the gas pressure to the broiler. If the gas pressure is too low, it can cause the flames to be low or go out.
6. Make sure the broiler igniter is properly seated and connected.

Yes they can. Turn the gas off and call for service. You can't fix it yourself, you have to be a registered gas appliance technician to work on any gas appliance. The dangers of gas. Two blocks from my house, we felt it. https://www.insauga.com/five-years-ago-today-natural-gas-explosion-in-mississauga-killed-two-rocked-neighbourhood/ ..

To convert the appliance pressure regulator from one gasto another, do either (1), (2) or (3) below: Your unit will beequipped with one of the three appliance pressureregulator types shown below.1. Remove the cap, push down and turncounter-clockwise. Turn the cap over and reinstall(figure 10).NOTE: The gas type you are converting to must bevisible on the top of the installed appliance pressureregulator cap.2. Remove plastic dust cover from cap nut on top ofappliance pressure regulator. Remove cap nut fromappliance pressure regulator (plastic dust cover comesoff with nut). "IMPORTANT" remove plastic dust coverfrom cap nut and reinstall on opposite side of cap nut.Reinstall cap nut to appliance pressure regulator andreplace dust cover. "CAUTION" be sure marking forthe type of gas to which appliance pressure regulatorhas just been converted is visible in top of cap nutbefore replacing plastic dust cover. (See figure 11).3. Remove cap and forcibly snap out plastic plunger frombottom of cap. Turn plunger over and forcibly snapback in original location (figure 12).NOTE: Plunger MUST snap into position; the gas typeyou are converting to must be visible on lower side ofplunge