Top 20
Jenn-Air JDR8895AAS Dual Fuel (Electric and Gas) Kitchen Range Questions & Answers
Where is the fuel pump fuse located 1999 gmc jimmy
Underhood fuse block- "ECM B" 20 amp fuse. It supplies voltage to the fuel pump relay in the same fuse block, which sends voltage down the line to the fuel pump when the engine computer turns the relay on.
10/11/2013 11:39:06 PM •
Jenn-Air...
•
260 views • 0 helpful votes
The lower oven heats up really slow and stops at
The problem may be caused by different components but most common is the oven temperature probe. It could also the the thermostat. A technician can measure the resistance of the probe at a known temperature and determine if it is failed or not.
10/30/2013 1:50:54 AM •
Jenn-Air...
•
131 views • 0 helpful votes
Turns on by self
from what i can find there can be a fault on the mother board but it does not say what.if yours is the tutch model it could be to sensitive also if there is a grease build up it could be shorting a circuit.
9/22/2013 3:49:15 PM •
Jenn-Air...
•
54 views • 0 helpful votes
Line diagram oven
Pull the temperature probe and with a multimeter, check the Ohms. It should read right around 1100 Ohms at room temperature. If you get any other reading replace the probe.
Here is that part to order.
5/1/2013 7:00:28 PM •
Jenn-Air...
•
77 views • 0 helpful votes
Jenn-Air JDR8895AAS error 1c1c
1C1C Shorted Key - Check wire harness connector and ensure proper connection and wires show continuity to the control board. If ok, replace the control board. Here is the part to order.All parts come with a 365 day, any part, any reason return policy.
2/4/2013 10:04:09 PM •
Jenn-Air...
•
659 views • 0 helpful votes
Jenn-air
What is the complete model number of your unit?
12/4/2012 11:58:45 PM •
Jenn-Air...
•
348 views • 0 helpful votes
Fuel pump/replacement
1Open the hood and prop it.
2Open the cover to the under-hood fuse box and locate the fuel pump
relay. You can find the fuel pump relay by reading the diagram under the fuse box cover.
3Remove the fuel pump relay by pulling it up with your fingers.
4Crank the engine for approximately 5 seconds and repeat three times. The engine won't start, because the fuel pump relay is removed and will just crank. The purpose behind this is to relieve fuel system pressure so that you can safely remove the fuel filter without fuel spraying dangerously.
5Locate the fuel filter on the passenger side of the engine compartment. It should be black and cylindrical with two fuel hoses attached to it.
6Unscrew both hose clamps with a screwdriver and pull the hoses off.
7Unscrew the bracket holding the fuel filter with a screwdriver and remove the fuel filter.
8Install a new fuel filter onto the bracket and tighten the bracket with a screwdriver
9Connect the two fuel lines to the new fuel filter and tighten the hose clamps with a screwdriver.
10Reinstall the fuel pump relay.
11Start the Kia Sorento and make sure there aren't any leaks. It may take a few cranks to get the fuel circulated through the system for the car to start.
10/23/2012 11:13:13 PM •
Jenn-Air...
•
86 views • 0 helpful votes
Oven temp won't take 300 and enter...i
do all other temps work correctly? if so it is probably in the control board or the thermo coupler is reading the pilot light temp as being already that warm...
7/4/2012 3:44:28 PM •
Jenn-Air...
•
85 views • 0 helpful votes
Not finding what you are looking for?
