20 Most Recent Pyle Dryver PLAD213 Car Audio Amplifier Questions & Answers

I have a plad213 what

2 4 ohm speakers wired in series is 8 ohms and then is dropped back down to 4 ohms when you bridge it.

2 4 ohm speakers wired in parallel is 2 ohms then dropped down to 1 ohm when bridged
(most amplifiers will not handle loads below 2 ohms)

hope this info helps

Pyle Dryver... | Answered on May 20, 2011

1 Answer

LIGHT RED PROTECTION

missmatched impedance, insufficient grounding or blown transistor/other internal problem within the amp.

Pyle Dryver... | Answered on Aug 05, 2009

1 Answer

Pyle dryver amp light protection stays on

check your subs disconnect them the try to power the amp up if it powers up the the subs have died and it could be a problem with that amp i suggest you get a better amp

Pyle Dryver... | Answered on Jul 11, 2009

1 Answer

AMP LIGHT STAYS ON PROTECTION

shorting out check your speakerwires, or a bad speaker, remplace them

Pyle Dryver... | Answered on Jul 10, 2009

1 Answer

Protect light will never go off

Unfortunately, it sounds very likely that you have a defective amplifier. Usually you see a protect light on an amplifier because of an internal short, supply voltage too high, voltage too low, or speaker connections of too low impedance or grounded. If your speaker wires are completely disconnected, that eliminates the most common external cause of a protect light. Also, a protect light from the voltage being too high is very unlikely without the engine running (and an alternator problem). The "other positive cable" you're referring to is the remote input, and it won't cause a protect light no matter how it's connected. You'd need a voltmeter to do much more troubleshooting; a protect light can be caused by a very poor ground connection, or it's possible that a poor connection at the battery or fuseholder, or a defective fuse, is causing a severe voltage drop. However, based on what you've described, it seems most likely to me that your amp is defective.

Pyle Dryver... | Answered on Jun 08, 2007

2 Answers

Amp problem help

your problem is in instalation of car moust driver your service car end fixed the problem of conection

Pyle Dryver... | Answered on Apr 23, 2007

1 Answer

1200 watt legacy amp not working right

your amp its protect by releas of [powerout]one this releys is dead you mast chenche

Pyle Dryver... | Answered on Apr 15, 2007

1 Answer

Pyle plbt72g. It isn't working. It just keeps blinking "welcome".

You could see if the companies official website has anything that can help you out.www.helpowl.com

Pyle Car Audio &... | Answered on Aug 10, 2020

1 Answer

How do I get my pyle radio from going back to calibration every time

The most common explanation for why a car's clock reset is suddenly is due to the battery.This can occur if the temperature has been frigid, the car hasn't been run for a while, or you've been messing around with the electronics after the engine was turned off.

Pyle Car Audio &... | Answered on Aug 03, 2020

1 Answer

Used the pyle flextreme mp3 earphones for about 3 months for swimming now suddenly its just not charging how to resolve

Your earphone capture some moisture in it, shake it or dry it properly for a while.

Pyle Car Audio &... | Answered on Jun 03, 2020

1 Answer

Pyle pd3000ba p/n key,video,time,setup,language,zoom,pcb,program,usb/dvd all frozen

No idea what your talking about.......

Pyle Car Audio &... | Answered on Dec 31, 2019

0 Answers

Replaced batteries in my new Pyle PMP53IN bullhorn. Used x1. Now can’t get it to work.

Pyle Car Audio &... | Posted on Aug 23, 2019 | Be the first to answer

0 Answers

Pyle PDAP18BK.5 only plays in mono why

Pyle Car Audio &... | Posted on Aug 20, 2019 | Be the first to answer

0 Answers

Pyle plbt72g 7" the screen mechanism not working and doesn't pull out the screen, I had to pull out the screen manually with my hand

Pyle Car Audio &... | Posted on Jul 14, 2019 | Be the first to answer

0 Answers

PYLE PLMRMBT7S what is the remote panel diameter?

Pyle Car Audio &... | Posted on Jul 10, 2019 | Be the first to answer

0 Answers

PYLE PLMRMBT7S whats is the remote control panel diameter ?

Pyle Car Audio &... | Posted on Jul 10, 2019 | Be the first to answer

0 Answers

The screen on my Pyle head unit is inverted. Everything is backwards3. What do I do?

Pyle Car Audio &... | Posted on Jun 18, 2019 | Be the first to answer

0 Answers

How to connect a Pyle-Home PSPVC4 4-Channel High Power Stereo Speaker Selector to a Denon Pro DN-333XAB amplifier speaker out euroblock connection

Pyle Car Audio &... | Posted on May 15, 2019 | Be the first to answer

1 Answer

Where can I get a repair manual for a PYLE PWMA-890UI without giving up total control of my computer?

You probably won't unfortunately. It's a $150 speaker. That means that the chances of having a service manual available are slim. Your best bet is checking the amp chip and the power supply. If anything is obvious you will find it.

Pyle Car Audio &... | Answered on May 09, 2019

0 Answers