20 Most Recent
NetGear WGR614 Router Questions & Answers
Wont connect to internet
You need to reset the router if the lights are flashing. Press the reset button at the back of the router for about 20 seconds then release it. Now unplug the power for 20 mins as well and plug it back in. Make sure your connection is right. PC connected to port 1 and modem to WAN or Internet port.
Cannot connect to Internet.
The orange blinking light indicates that it cannot obtain the DNS server from your ISP (internet service provider). You must contact your ISP and check whether your service is active.
How do I make this
No, you have a bad internet connection.
Sort that out first, try not to use wireless connection until you have established a good fixed cable connection.
Then test out the wireless connection.
Want to lock my netgear browser
Netgear is not a browser. It is a Router. For the sake of this question I would assume you were talking about the Router, what do you mean by "Lock"? You can change the default password, and no one will be able to access it. If you only want specific devices to connect to the router, you can:
1) Enable MAC Filtering
2) Disable DHCP, and assign Static IP addresses to the devices
3) Hide SSID (Not Broadcast it)
Wireless internet wont connect
Go to windows logo
in search box type cmd
in black screen type ipconfig /release
when completed type ipconfig /renew
try again if still no go do the following
reset to factory default
press and hold reset button during the whole process and only release when completed.
1)press reset button 30 seconds
2)remove power cable 30 sec
3)plug in power cable 30 sec and then release.
You should no be set for 192.168.1.1
username admin
password is password
If all fails check to see if the box is checked for wireless
How do I get my Blueray and my TV to connect with the Netgear wireless?
First off you need to have a wireless connection,that being said if you have one then you will need to go to your device and let it search for your wireless router.Once that is done and you enter any password you may have on your router it should connect.I seen had issues with this because the wireless signal can be weak if so to resolve this use a POE (Power Over Ethernet) or a direct wire from your router and select a wired connection.
Forgotton name and password
have you tried admin and password? The defaults if you haven't changed them.
Or if you did.
Reset for most routers with a reset button on the rear panel
Write down configuration information such as IP addresses, security keys, opened ports and services, etc., that you modified. (The default username is
admin and the password is either
password or
1234. Try these before resetting the router.)
- Press the reset button on the back until the test light blinks. This takes about 10 seconds. (To avoid accidental resets, the small button is recessed. Use a pen or paperclip to access it.)
- Release the button.
- Wait for the router to reboot.
- Log in with the default password.
If the router was not cleared, try these additional steps AFTER the router has finished rebooting.
- Unplug the router's power.
- Press and hold the reset button. While the button is held down, reconnect router's power.
- Continue to hold the reset button for 20 seconds after reconnecting the power.
- Wait for the router to reboot.
- Log in with the default password.
Download smart wizard instalation assistany wgt 624
Connect a LAN cable from the Netgear to the LAN port on your computer, open a browser and enter the Netgear configuration URL - http://192.168.0.1 The default login = admin The default PW = password You can now change the default admin password and configure the wireless settings. Go to the wireless configuration and set up the SSID and WPA or WPA2 encryption to protect your wireless network and Internet from unauthorized access. Now apply these settings to the wireless card in your laptop/computer. To secure your wireless network from unauthorized access, please click on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security
Not finding what you are looking for?
