20 Most Recent Asrock ALiveNF6G-VSTA (MB-ALVNF6G) Motherboard Questions & Answers

google translated to ENGLISH you said, (i hope) "After having done all the checks with the router and the cpu connection and having tried other computers the problem is the following: every time I turn on the computer I have to restart to be able to surf the internet, and once restarted I can surf but not before . So the problem must be with the motherboard. I would appreciate a solution, as it is very annoying." AND COMMON ! NO OS TOLD AT ALL AND MATTERS FIRST. XP,VISTA , 7? WHAT? OS IS THERE. upgrading any OS past what Asrock allows gets you dead , LAN AND DEAD SOUND. (and more) answer, 1: tried other computers<<< and what happened on them.? all the same or only 1 PC fails and not told ethernet or wifi connected. so answer are super hard, but i bet Ethernet works other PCs cabled to router. the CPU has no LAN, sorry, the mobo does have LAn CALLED ETHERNET.(wired). and the chip is known, (in the manual) no lan told.(wifi or wired) there is no wifi on this mobo, so must be this, wired below. Realtek PHY RTL8201CL - Speed: 10/100 Ethernet (slow kind) to use this chip on thIS MOB\O BOARD, WE must load the driver first from asrock (using a 2nd PC to fetch it and put it on dead lan PC)_ the drivers are frozen at XP/ VASTA OS. LONG AGO 2006 YEAR. LOAD ALL 6 DRIVERS SEE HERE. (PICK OS FIRST) https://www.asrock.com/mb/nvidia/alivenf6g-vsta/#Download ELSEWHERE YOU GET A VIRUS, I PROMISE, BESIDES BELOW. OR IF LUCKY DIRECT FROM CHIP MAKER HERE THE 81-nnnn driver is no good for 81. so finding it here is not easy. https://www.realtek.com/en/component/zoo/category/network-interface-controllers-10-100m-fast-ethernet-pci-software

You need to reset bios.
Open cpu cabinet and pull cmos cell from motherbord chipset for 15 minutes then all settings are factory defaults.
Aslo you can reset settings with jumper settings .
Refix your RAM memory. Refix processor.
Reattch ATX power supply to motherbord.
Thanks for using fixya.
Please rate solution if it helps.

Hello download the manual here:http://www.elhvb.com/supportbios.info/Archives/MANUAL/ABIT/nf8_series.pdfYou need a PDF reader to read content.Good luck

check weather the front usb cables on mother are connected properly or not or alse try another connecting other usb device

Restart your computer During the boot process you will see on the screen to press a certain key to enter setup Press and hold that key during the boot up process to enter BIOS using the arrow keys load failsafe defaults or load optimized defaults press escape then press f10 to save to cmos to restart hope this helps you

take a look at the motherboard manufacturers website and see if your motherboard will accept a 4400. You may need to update the bios on your board to accept the faster processor. You need to be careful if you flash the bios. do it wrong and you can write the board off.

Good luck

Try to clear CMOS with the jumper, and also unplug battery of CMOS for at minimum 15 mnutes. Then, return the jumper in his place and plug the battery. After turn of computer and see if monitor will show the view....

Hi There,

Firstly, disconnect everthing from the Power supply EXCEPT the motherboard

1. Does the fan on the CPU spin when switching on?

Double check power switch connections to motherboard, sometimes if connected incorrectly, it may stop the board from powering up.

2. Attach the PC speaker to motherboard and remove RAM, REMEMBER to follow all antistatic rules when doing anything inside the computer.
Switch machine on and listen if it makes a sound. if it does then the motherboard is fine.

Have you recently fitted the board yourself?, if so make sure it is not earthing on to the casing.


Try these first and let me know how you go.


neil

Yes, the ASRock alivenf6g-vista is compatible with Windows 7.

One bad lead can cause a computer to continue on a cycle or to shutdown or fail to detect your hard drive

Test all leads that attach to your hard drive including electrical extensions,IDE,SATA

the leads from your ((motherboard to your hard drive)) make sure they have a secure connection and are not faulty or just replace them there probably old and faulty make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty even the electic extensions or just replace them they are probably faulty a computer needs its connections to have an end so any faulty leads will end up with a computer error hope this helps don

The onboard LAN chip has been fried. Disable it from the BIOS and install a separate PCI LAN card.

Visit
http://www.asrock.com/support/index.asp

Whoever is telling you that you need Vista for this motherboard to operate is very much mistaken. Also the hard drive you are using makes no difference either. What could be causing the problem is listed below:

1. Check the Power supply is good and the connections to the hard drive, motherboard and the voltage is set on the back of the PSU to the voltage for your country. In any event, the only way to test a PSU is to replace it.
2. Check the CPU fan and CPU cooler are sited correctley and in firm contact wth the mobo and that the fan is plugged on the mobo and working.
3. Check that there are no bulging or blowing capacitors on the motherboard and no signs of burned traces on the pCB
4. Listen for any beeps as the thing powers off, repost if you hear any
5. Check memory is seated correctly, remove each module in turn and replace and test, fill the yellow slots first before you place any in the red slots, check the modules you are using are the same speed.
6. Check the power button on the computer is free to move and does not stick
7. Check the SATA cable is firm fit on the mopbo and hard drive, replace and test if you think it may be damaged.
8. Try another Sata hard drive, yours might be internally damaged.

Repost if you get no luck

For a casual gamer without too much money
http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=6759736&CatId=1558
For an avid gamer with sufficient funds
http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=6506550&CatId=1558

If you need RAM, and you do not intend to OVERCLOCK or use the PC with lots of programs running at the same time, cheap and cheerfull RAM will be ok, I would advise to buy from a Good manufacturer, but the budget or value Ram will be fine.
The more expensive RAM with tighter timings, and higher speed ratings will work faster in the right circumstances, but for most people, it will be a waste of money.
Buy the best you can afford

please reinstall your bios 

folloow the link and fill out the ppw with asrock.
http://www.asrock.com/support/tsd.asp