Intel D102GGC2 Motherboard - Answered Questions & Fixed issues

If the motherboard is a 4 slot dual channel memory configuration you have to install the memory in slot 1 and 3 or 2 and 4.

1. pls read the user manual first to identify which pinds of password jumper to normal position
2. Reinstall the jumper in a different position. For example, if you removed the jumper from pins 2 and 3, reinstall the jumper over pins 1 and 2.
3. Replace the computer cover and reconnect the power cable and monitor.

You can now assign a new system and/or setup password. For more password information, refer to the Passwords section of your computer'sservice manual.

INFORMATION.

www.intel.com/support/motherboard/desktop/d102ggc2/sb/cs-026579.htm#dimms

Hi! Try this web site, it will help you a lot... http://drp.su/download.htm its free!, try to use USB to copy or any peripherals you can use to copy the software, it will help to install the needed driver of the Motherboard. Good luck!

take out battert then wait 1 min then put it in

take out the cmos battery

take out the battery for cmos

http://www.bing.com/search?q=ATI+Xpress+200+Windows+7&FORM=QSRE1

audio driver for high deffination
the mother board is foxconn 945 - cmx series

It support both SATA and IDE HDD

You may install i Terabyte SATA HDD without any problem

it should be fine

Sometimes it passes a poorly designed ram test, probably faulty ram, speeds always default to the slower of a pair. Some computers need all slots full. Did you buy it new? We have Re-PC for used components in the Seattle area, a great resource.

FSB speed is what the RAM works at. If you get faster RAM that is ok, it will work but only at the FSB speed. If you get slower RAM then it works at the slower speed or may cause issues.

http://downloadmirror.intel.com/15112/eng/D102GGC2_TechProdSpec.pdfthe most easy way are just to remove the CMOS-battery for10-20 seconds.looks like a watch-battery.now you have reset BIOS.

First of all Check SMPS whether it is giving proper output Voltage to the board., then do change the RAM., the same problem again persists better to delete all partition and reinstall OS

Mother board d102ggc2 • Support for DDR2 533 MHz and DDR2 400 MHz DIMMs • Support for up to 2 GB of system memory

Hello here is the homepage:http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Desktop+Boards&ProductLine=Third-Party+Chipset+Boards&ProductProduct=Intel%C2%AE+Desktop+Board+D102GGC2More mainboard info here in pdf format:http://downloadmirror.intel.com/15112/eng/D102GGC2_TechProdSpec.pdfHere is no graphic drivers for windows 7Add a graphic card on the mainboard that supports windows 7 in the PCI Express x16 add-in card connector.Or try to download and install the 32 bit vista driver from here:http://support.amd.com/us/gpudownload/windows/Legacy/Pages/radeonaiw_vista32.aspx?type=2.4.1&product=2.4.1.3.13&lang=English Here the 64 bit:http://support.amd.com/us/gpudownload/windows/Legacy/Pages/radeonaiw_vista64.aspx?type=2.4.1&product=2.4.1.3.13&lang=EnglishHope this will help you

Hello here is the homepage: http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Desktop+Boards&ProductLine=Third-Party+Chipset+Boards&ProductProduct=Intel%C2%AE+Desktop+Board+D102GGC2You can only add 1gb per slot Because the mb does not supports a bigger module.This ram type does come as 1 gb module.The 667 mhz and 800 mhz is the Mhz speed for the ram module.Your mainboard supports this but it will only run the current front side bus speed as the mainboard supports.This means that the new ram will only run 533/400 mhz as the mb supports.Hope this was helpfull

Laptop or Desktop ??You may have inadvertently hit a certain combination of keyboard strokes programmed to send the laptop into sleep or time-out mode. Hitting the space bar, power button, "ESC" or other random key should restore the display.

test all power and data leads that attach to your hard drive the leads from your

(motherboard to your hard drive) Sata make sure they have dust free secure connections and are not faulty make sure all leads that are attached to your drives dvd\cd have secure connections and are not faulty

even something as small as a faulty fan lead can cause you problems a computer needs all of the power and data to travel through every working device and to

have an end for a computer to be able work properly

make sure your graphics card is securely seated with no dust

click start control panel display desktop you can select a different desktop from the drop down list or a browse button where you can select different pictures this may vary depending on your operating system also you can change the settings for more or less pixels or from the drop down list pick the appropriate level of color range or troubleshoot also select advanced then general dpi normal size larger size or custom settings always click APPLY after making any changes

if you remove the graphics card to clean the socket replace it

restart the computer the found new hardware wizard should activate

hope this helps