20 Most Recent Frigidaire AEQ7000EG Affinity Series Electric Dryer - Page 2 Questions & Answers

check out these sites... https://www.repairclinic.com/ProductDetail/689318?symptoms=1 https://www.appliancepartspros.com/repair-help/frigidaire-dryer-aeq8000fe0-repair/aeq8000fe0-wont-start.html A call to their tech 800#s so you don't start throwing parts at it. :) Best to you

The Frigidaire AEQ8000FE electric dryer is displaying the 50 and start/stop lights blinking randomly with periodic beeping. Pressing the control panel clears the issue, but it returns after a few minutes. Despite this issue, the dryer is working properly.

The loud, constant squeak/squeal from your Frigidaire dryer, combined with a burning smell, indicates a serious problem that needs to be addressed. While replacing the drum bearing kit was a good step, it appears that there may be other issues at play. One possible cause of the squeaking could be a worn or damaged drive belt or idler pulley. If the idler pulley spring came off, it is possible that the belt is not properly tensioned and may be slipping or rubbing against the drum, causing the squeaking noise. Additionally, a slipping belt can generate a burning smell as it heats up from the friction. Another possible cause of the burning smell could be a malfunctioning heating element, which may be overheating the dryer and causing the burning odor. It is recommended that you stop using the dryer immediately and unplug it from the power source. It is not safe to continue using a dryer that is producing a burning smell.

f the outside of your Frigidaire dryer is hot to the touch and the heating element appears to be glowing red hot when the knob is not in the off position, it is likely that there is a problem with the dryer's heating element. It could be shorted, burnt, or damaged in some other way. It is also possible that there is a problem with the dryer's thermostat, which regulates the temperature inside the dryer. If the thermostat is not functioning properly, it could cause the heating element to stay on for too long and overheat the dryer. It is recommended that you stop using the dryer immediately and unplug it from the power source. It is not safe to continue using a dryer that is overheating or has a malfunctioning heating element. It is best to have a qualified technician inspec

It sounds like you may be experiencing issues with the heating element on your Frigidaire window AC/Heater combo unit. Here are a few things you can try to troubleshoot the problem:

1. Check the thermostat: Make sure that the thermostat is set to "Heat" and that the temperature is set to a level high enough to activate the heating element.
2. Check the air filter: A dirty air filter can restrict airflow and prevent the heating element from functioning properly. Clean or replace the air filter if necessary.
3. Check the heating element: The heating element may be faulty and needs to be replaced. Consult the manufacturer's manual or contact the manufacturer's customer service for further assistance.
4. Check the blower motor: The blower motor may be malfunctioning and needs to be replaced by a professional technician.
5. Check the wiring: Check the wiring and connections, ensure that all the wiring is securely connected and that there is no damage to the wires.
6. Check the fuses: Make sure that all the fuses are working properly and that they are not blown or tripped.

Keep in mind that attempting to repair an AC/Heater unit can be dangerous if you are not familiar with the proper procedures and safety precautions. It's best to let a professional technician handle the repair. If the problem persists, it's recommended to contact the manufacturer's customer service or a professional technician for further assistance. They can inspect the unit and determine the cause of the problem and provide a solution. Regenerate response

The control panel lock is engaged. This keeps the dryer from being turned on by accident while cleaning the panel (or by a small child). There should be a line with a padlock symbol between two buttons on the control panel indicating the ones to press and hold to toggle the lock feature. On some Frigidaire dryers, the buttons to press and hold are Options and Select. You need to hold the buttons for 10+ seconds. The LOC message should disappear when you have held the buttons for long enough. However, if you do not release the buttons, the lock will toggle back on. I hope this helps. Cindy Wells

Good morning, dissapointed81. I understand that you are experiencing some concerns with your dryer. Before contacting a service provider, I would suggest that you either unplug or turn the circuit breaker off to the unit for five to ten minutes. Let the dryer reset completely and try to use it as normal again. If this does not prove to be effective, we do recommend that a professional technician diagnose the thermal limiter and control board. The E66 error code typically indicates an error within the thermal limiter and interrupted communication to the control board. Though a full repair, and replacement parts, might not be needed we do recommend having a professional test the unit for safety reasons. -Hope this helps!

POSSIBLE BAD ROLLERS, BAD DRUM GLIDES, WORN BELT, DAMAGED BELT TENSIONER? AND BAD FELTS ON THE DRUM ITSELF

Question edited for clarity. I can think of two things. First wash the lint filter with dish soap and give it a gentle scrub with a plastic pot brush. Fabric softener can gum them up and impede the air flow. Check the hose at the back for lint build up in the hose itself and in the tube at the back of the dryer. Finally check the flaps on the wall vent for smooth operation and they they are opening fully. If you have the old type with a circular flap, you might even find a birds nest in there! Although the error light is telling you to clean the lint filter, it is actually registering reduced air flow and an overheat situation. ..

The voltage or AC hertz mains supply to your house has become out of specs. https://www.google.com/search?q=affinity+dryer+ea1+error+code ..

Sounds like the door switch is bad and the unit is acting as if the door is still opened even when you have it closed. Here is the switch for your unit.

Yes, never ever use the self clean function on modern ovens. 880-900 degrees to too aggressive. We see ovens broken here all the time, doors locks broken, wiring burnt, elements burned out, control boards frazzled, fans seized. You need a service call. There is no thermal fuse for obvious reasons, it's an oven. Self-Clean Ovens The oven is cleaned by heat, at temperatures above normal cooking temperatures. During the cleaning cycle the oven is heated to about 880 degrees Fahrenheit (471° C.). At this temperature, food soils inside the oven decompose, leaving behind a small amount of ash. Buy a can of Easy-Off, or use household ammonia. If panels are removable, you can put the parts and the ammonia into a black garbage bag overnight.

Probably the main burner safety valve. Possibly a fault with the fan. It is a gas appliance so you can't work on it yourself. You need a gas certified appliance engineer to diagnose and fix.

The model number is probably FDE437GHS0. Many Frigidaire manuals are available here: http://b2b.frigidaire.com/support/manuals.asp . You don't need the entire model number to get the owner's manual. The current link to the owner's manual is ftp://ftp.electrolux-na.com/ProdInfo_PDF/Webster/131883500en.pdf . A quick link to the Operating instructions is ftp://ftp.electrolux-na.com/ProdInfo_PDF/Webster/131929400.pdf . I hope this helps. Cindy Wells

Hello good day, The E means error ! This means that you need to follow the operation seating to be able to operate it again or you we have to reset the dryer again. Thanks, Good luck.

This indicates it is the High Limit Thermostat, which isn't a fuse. Most dryers have three heat related components. They usually trip because of bad airflow, check the hose at the back and the vent in the wall. This is the time that birds make nests in them! Also wash the lint filter with dish soap and a brush. Part No. 33 here https://www.searspartsdirect.com/model/55b2zm5szl-001428/frigidaire-fase7073lw0-dryer-parts The error code of E65 is a high limit thermostat trip . For Electric Model, check Inlet Thermal Limiter for continuity. If Thermal Limiter is open, check for evidence of high temperature event and any resulting damage. If no further damage is evident, replace Thermal Limiter. Jul. 27, 2017

Frigidaire dryer still codes E65 after an E64. Replaced heater ...

https://www.justanswer.com > ... > Dryer Vent Problems

Did you hold button for at least 5 seconds?

Could be cycle timer failure

check your dryer vent system, may be blocked causing the dryer to over heat and turning off so there won't be a fire.

E61 is a stuck relay on the main control board. This is the board right behind the control panel where all the buttons are. You'll need to order and replace this board.