20 Most Recent Electrolux ICON Designer E30EW75GSS 30" Single Electric Wall Oven with 4.2 cu. ft. CustomConvect3 Convection Oven, 3 Smooth-Glide Racks, Temperature Probe, Halogen Lighting and Wave-Touch Control Panel - Page 8 Questions & Answers

Thank you for your post, Richard Gardner! I understand that you need to replace the element inside of your Electrolux wall oven. I was unable to locate any specific step by step instructions on the removal and installation of your element. I have attached a copy of your parts manual and that provides a breakdown of all the available parts within your wall oven. If you need further assistance I would recommend having a professional technician out to properly remove the element and install the replacement part. I hope this information is helpful to some degree. -Matt

For a more precise answer I need more information like is it light illuminates when the failure is occurred. If the light illuminates then is faulty oven thermostat. If the light does not illuminates then is faulty main temperature limiter. Dado

From my experience the most common reason for this failure is a thermal switch for cooling fan. It is located on the upper side between the wiring and its function is to switch off the cooling fan when the temperature drops even though the oven is already turned off. If the cooling fan does not work then it will increase the temperature on the cabinet and the main temperature limiter will switch off the oven. Dado

It is good practice to specify model of appliance (like EOG9330XN). Probably means temperature range of oven sensor exceeded (for more than 5 seconds). Dado

Good Morning Scott Robert, thanks for your post! Based off the information you have provided you would like to remove the flat top from your Electrolux range. Regrettably this is not a simple DIY job. I would recommend having a professional technician out to disassemble the cooktop and install any new electrical component. This will help to avoid any future issues or personal injuries. Good luck. -Matt

Hello Rasheda, this is Z. Thank you for your post! If you are getting an error code F68 on your Electrolux oven, it typically means that your appliance may be experiencing an issue with the incoming line voltage. One of the best ways to determine if this is a false error code is to rest the power to your oven by either unplugging it or flipping off the breaker for about ten minutes. If the error code persists, it would be advisable to contact an experienced appliance repair tech since this is not a simple DIY job. He/she would need to determine whether the problem rests with the power supply voltage or EOC (Electronic Oven Control). I hope this helps explain the error code you are receiving.

try to turn off breaker then turn on again

Thank you for your inquiry, friend!

Based off the information you have provided your Electrolux oven is not heating properly. I would recommend performing a reset on your range which you can do by disconnecting power from it for ten minutes. If that does not help to correct your issue it could be a faulty element or control panel. I understand your range is only six months old typically the warranty for a range is one year. I would contact the manufacturer for proper resolution regarding a warranty. I hope this is helpful. -Matt

Hey friend, thanks for your inquiry!

From what you have described it sounds like a potential issue within your gas supply or burners. I would recommend reaching out to a professional technician to come out and properly diagnosis your appliance. I hope this is helpful. -Matt

Hey Tatiana, thanks for your post!

I understand that your Electrolux range is flashing "F50". I would recommend resetting power to your appliance and you can do that by unplugging or disconnecting power from your appliance for roughly ten minutes. If that does not correct the issue it could be a problem within your EOC (electronic oven control) or UIB (user interface board). Since it could be any one of these underlying issues I would advise to have a professional come out to your home for proper diagnose your appliance. -Matt

If you're talking about the acrid smell immediately after starting the oven, that's aldehyde gas, a byproduct of cold gas combustion where the flame contacts the cold metal oven surfaces. That smell should disappear within the first minute or two, and it's entirely normal for a gas oven. If you're talking instead about the smell of fuel gas, then your burner may need to be adjusted; it may be running much too "rich".

The oven has 2 igniters. One for the broiler and one for the oven. We had a similar problem but the oven had no flame. The broiler worked fine. If there is no flame than you are going to smell gas since it is not being combusted. The oven igniter is in the bottom of the interior oven. The bottom plate is removable. Since there are openings in the panel sometimes debris falls through and some debris can accumulate.In our case there was some aluminum foil blocking the igniter and a simple cleaning fixed the problem.

my acoustic solutions tv is stuck in standby mode its the timer because it com on the other day how do i turn timer off

Hey Margaret, thank you for your post!

I see you are looking for video regarding your Electrolux oven. I would like to ask for some additional questions to better assist you. Is there a certain feature or option you are looking for assistance with? Also are you able to provide model number, with that information I can research any further questions you may have. You can locate the serial tag (which lists your model number) behind the bottom drawer of your range. Thank you for the post and I look forward to assisting you. -Matt

Good Morning Friend, I understand you were using the stovetop and oven on your Electrolux range. You heard a loud pop, and are wondering what happened. I suggest contacting your local authorized dealer for further assistance. They have been trained on your appliance and should be able diagnose your appliance and determine what cause that loud pop. -Best Regards- WP

Good Afternoon Friend, I understand that your Electrolux double oven is not heating up, even though the fan is running. I suggest resetting your appliance, be either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. If further troubleshooting is needed, please leave me your model number, so I am able to better assist. Hope this is helpful. -Best Regards- WP