20 Most Recent Whirlpool 24 in. DU1148XTP Built-in Dishwasher Questions & Answers

0helpful
1answer

ALL LIGHTS FLASHING ER S

push cancel if that doesn't work cut the power to it for about an hour
6/10/2014 8:01:47 AM • Whirlpool 24 in.... • Answered on Jun 10, 2014
0answers
0helpful
1answer

After all of the cycles

Hi

If the water inlet valve is fine and it fills with water then the issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that fills the dishwasher lifts the float, and when it reaches a certain level, it acts as a trigger for the float switch. The float triggers the float switch to shut off, thereby shutting off the flow of water into the dishwasher. A defective switch may interfere with dishwasher's filling and/or draining ability. Use voltmeter to test the switch. Set the device to the ohms setting x 1. Take each probe and touch them to one switch terminal each. This should produce a reading of either zero or infinity. Continue to touch the probes to the terminals, and press down on the switch's button. The reading should change to the opposite extreme. If the switch fails either of these tests, you should replace it. Hope this helps...please post back for further assistance.

Daniel

6/27/2011 12:57:07 PM • Whirlpool 24 in.... • Answered on Jun 27, 2011
0helpful
1answer

Whirlpool dishwasher not cleaning dishes

Hi, I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance DishwasherResidue and Film on Dishes

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes




'; ';
5/14/2011 11:43:45 PM • Whirlpool 24 in.... • Answered on May 14, 2011
0helpful
1answer

There is a white film all over the dish's when it

Hi,
There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....

Dishwasher Repair Problem Detergent Cup does not Open

heatman101
5/14/2011 11:38:20 PM • Whirlpool 24 in.... • Answered on May 14, 2011
0helpful
1answer

Hightemp light flashing

Hi
To resolve this error try pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air Dry - High Temp - Air Dry or Hi Temp Scrub, energy saver dry, Hi Temp Scrub, energy saver dry. Now let the unit run for 2-3 minutes and then you press the Cancel/Drain button and allow it to completely drain and reset. If this doesn't work then it's an issue with the wash pump not pumping the water past the heater efficiently or due to lack of water to heat. Please make sure that heater is not open circuited and is heating the water efficiently. You'll have to check the heater using a multimeter; the meter should read between 3000 to 3300 ohms (Use multimeter on Rx1 ohm setting). If heater is fine then make sure water pressure is optimum and fill valve is working fine. Hope this helps...please post back for further assistance.
Daniel
5/5/2011 2:41:57 PM • Whirlpool 24 in.... • Answered on May 05, 2011
0helpful
1answer

Dishes are filmy at end of cleaning cycle.

Hi,

The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.

Here is a tip that will help you to solve the problem of films, residue, and scum in your dishwasher.

Dishwasher Residue and Film on Dishes

heatman101


2/24/2011 5:54:20 PM • Whirlpool 24 in.... • Answered on Feb 24, 2011
0helpful
1answer

Very low water flow on the upper deck of the

Hello & Welcome to FixYa

Though you can reset the control by pressing two buttons in sequence 3-4 times:

High temp wash-heated dry-high temp wash-heated dry

If it won't work after the reset then I believe the water inlet valve needs replacement. Please get back to me if you have any other questions.

Kevin
2/1/2011 6:40:40 PM • Whirlpool 24 in.... • Answered on Feb 01, 2011
0helpful
1answer

Dishwasher was giving off a

Have you checked that the filters on the hose inlets are clear? Turn off water and undo hose to check, there is a small filter in the inlet. Have you checked that the outlet hose and trap is clear and that it can pump the water out? Have you cleaned all filters? The noise could be the pump blocked or unable to empty.
1/25/2011 4:04:20 PM • Whirlpool 24 in.... • Answered on Jan 25, 2011
0helpful
1answer

The front panel doesn't work

May just be the door switch(s)
11/20/2010 5:23:46 AM • Whirlpool 24 in.... • Answered on Nov 20, 2010
0helpful
1answer

Clean light is flashing

Hi

Thanks for using FixYa.
To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...


-high temp wash

-heated dry

-high temp wash

-heated dry


Please rate the solution if the issue is resolved or post a comment for further assistance.

Thanks

Rylee

11/18/2010 12:26:10 PM • Whirlpool 24 in.... • Answered on Nov 18, 2010
0helpful
1answer

I have a whirlpool had

Did he say it would be $65 for the fuse or for the fuse and labor?

If he's charging $65 for just the fuse then he's ripping you off. If his quote includes labor, then it's a fair price as the tech will have made 2 visits to you.

If you're unhappy with his price for the fuse and you are CERTAIN this part will solve your problem, you could buy the fuse and fit it yourself if you are competent - or pay a different tech for fitting only, with the part supplied by you.

Hope this helps.
10/28/2010 10:24:11 PM • Whirlpool 24 in.... • Answered on Oct 28, 2010
0helpful
1answer

I have a whirlpool had a tech come out to look at

I found the same part listed at pcappliancerepair.com for about $15.

You have to remember that repair technician fees include the diagnostic charge (diagnoses of your problem), the labor charge (to install the part - which is usually a set fee set by the company they work for) and the cost of the part. $65 dollars for a COMPLETE repair job is not a bad price. However, if he is charging you $65 for just the bi-metal (fuse), then you would be better off ordering the part and installing it yourself. This is not a difficult repair and can be accompished by any do-it-yourselfer with a little guidance.

If you need further assistance, please post back and let me know. I hope this helps you.
10/28/2010 10:08:44 PM • Whirlpool 24 in.... • Answered on Oct 28, 2010
0helpful
1answer

I have a DU1145XTP. The lock light button is on

To turn on Lock:

Press and hold Heat Dry for at least 4 seconds. The Locked light

glows. If you press any pad while your dishwasher is locked, the

light flashes 3 times.

To turn off Lock:

Press and hold Heat Dry for at least 4 seconds. The Control Lock
light turns off.

Good Luck please accept the answer

10/25/2010 5:46:58 PM • Whirlpool 24 in.... • Answered on Oct 25, 2010
0helpful
3answers

I have a model du1145XTPQ dishwasher. I doesn't

The dishwasher has a float switch which detects if the dishwasher is filled. If the travel of the float is not sufficient it may be triggering early and causing the inlet valve to shut. Also see page 21 in the user manual "dishwasher will not fill".

See this diagram for the water inlet circuit. The other possibility is the inlet hose is blocked. I am assuming the water inlet tap under the sink is fully open.

Please post a comment to indicate if this helped or not.
10/24/2010 11:06:47 PM • Whirlpool 24 in.... • Answered on Oct 24, 2010
0helpful
1answer

My DU1145xTPQA whirlpool dishwasher is not

Hi, I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works like new... However I have also found that if theheating element goes bad then that also can mess things up bad... So I wouldbuy new spray arms, and also check out the heating element to make sure it isworking... Here is a tip that will help you with the online buying...
Dishwasher Spray Arms not Spinning

How to Buy Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

Asker's Testimonial " explanation very clear. will give it a go and seehowsimple it was. thanks Ronnie " - ronnieshomes
10/16/2010 3:57:42 AM • Whirlpool 24 in.... • Answered on Oct 16, 2010
0helpful
1answer

Door won't lock - so it will not start

make sure it not hitting the cabinet some where
9/30/2010 1:54:49 AM • Whirlpool 24 in.... • Answered on Sep 30, 2010
Not finding what you are looking for?
Whirlpool 24 in. DU1148XTP Built-in Dishwasher Logo

62 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Oloyede Monsuru

Level 3 Expert

1468 Answers

Mike

Level 3 Expert

4377 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Dishwashers

  • Whirlpool Dishwashers

Most Popular Question

dishwasher giving off

  • Dishwashers
Loading...