20 Most Recent
Whirlpool 24 in. GU1200XT Built-in Dishwasher - Page 7 Questions & Answers
I have a quiet parner whirlpool dishwasher and the clean light is blinking
There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps to determine which component is at fault.
My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination.
The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again.
I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:37:33 PM •
Whirlpool...
•
Answered
on Jun 14, 2019
My whirlpool gold start button won't start at all it gives me a (start ?) and won't turn on at all. I hope you can help.
Jen
There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps.
My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination.
The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again.
I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:33:48 PM •
Whirlpool...
•
Answered
on Jun 14, 2019
Whirlpool quiet partner II Can not select cycle or cancel. Is there a factory reset?
You should find a trouble shooting document behind the kick panel of your machine. Follow the steps.
My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination.
The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again.
I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:31:52 PM •
Whirlpool...
•
Answered
on Jun 14, 2019
Replaced circuit board and fuse on whirlpool dishwasher and lights still flashing and won't do anything??
My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination.
The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again.
I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to! This may still be the problem after you replaced the control board.
6/14/2019 10:28:49 PM •
Whirlpool...
•
Answered
on Jun 14, 2019
Whirlpool dishwasher normal and pots/pan lights flashing
My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination.
The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again.
I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:16:37 PM •
Whirlpool...
•
Answered
on Jun 14, 2019
Whirlpool dishwasher gu2400 pots and pans light blinking
I had this problem. Fixed it but not sure what i did. I suspect it was either a temporay short, moist connection, or sensitive door latch. I shut off the circuit breaker and let stand for about a week. Perhaps it is drying. Turn back on, and the lights maybe blinking again, but press cancel button. The 2 minute drain will go on, let it drain and wait. The lights may still be blinking but wait 5-10 minutes and it may reset like mine did. You may have try this process a few times, like i did. I was playing with the door a bit too, firmly open and close. Hope this helps.
5/13/2019 2:41:39 AM •
Whirlpool...
•
Answered
on May 13, 2019
Flashing light 6 times, whirlpool dishwasher ADP4501
I had the same problem with a Whirlpool ADP 6515, led flashes 6 times, pause and repeat. Open the door, remove the 2 screws that hold the control panel (1 top left, 1 top right). Gently lift the control panel up and away from the door to reveal the wiring, controllers etc. My controller was a Flextronics UCB-IC-EBL-P7-M3-HE1. Look at the connectors, one of them is marked on the controller as NTC and has 2 blue wires, push down on the white plastic tab below it and disconnect it (pull it horizontally away from the controller)..I used a multimeter on 200k range and measured the resistance by probing those 2 blue wires and the NTC temperature sensor measured about 50k ohms +/- 5k depending on the room temperature. And that is correct for that NTC. (I knew the NTC was good as I had removed it from underneath the machine previously and measured the resistance whilst holding it under the hot tap as it went from cold water to hot. It's a Negative Temperature Coefficient sensor so the resistance reduces as it gets hotter).So problem was definitely not that. Solution was simple, on the connector itself, just use a very small flat bladed watchmakers type screwdriver to clean the pin contact faces and then gently pinch the pins of each wire closer together so that they bites tighter onto the controller.when you reconnect it.Refit the control panel and problem solved.Conclusion; the contact resistance of the connector to the controller added to the total resistance of the NTC and made the dishwasher think that the water was below the safe activation of the motor cycle, e.g. it thought the water was iced up.Job done !
4/17/2019 11:41:33 AM •
Whirlpool...
•
Answered
on Apr 17, 2019
Whirlpool gold quiet partner 111 is noisy during the whole cycle
Some dishwashers have soft food disposals. If something gets in this disposal that will not dissolve such as bone, pop corn kernels, broken glass. This will make noise throughout the cycle. Sometimes after many cycles it will grind itself away. Otherwise service would be needed if you don’t know how to get inside the pump.
4/2/2019 6:21:48 AM •
Whirlpool...
•
Answered
on Apr 02, 2019
Not finding what you are looking for?
