20 Most Recent
Whirlpool 24 in. GU1200XT Built-in Dishwasher - Page 3 Questions & Answers
Water in the dishwasher after the the cycle is complete
Two things to consider....clean water or dirty water?
Clean water usually indicates the fill valve is not shutting off all the way and the fill valve is "weeping" water in all the time = new fill valve time!!
Dirty water usually is not a dishwasher problem but more of a plumbing issue. Often the sink drain that carries the sinks water outside is not fast enough and some of this sink water is backing up into the drain hose and filling up the dishwasher through the drain hose. The drain from the sink to outside needs attention as this type of a problem indicates a slow house drain for that sink.
The dishwasher drain line should be clamped to the top underneath part of the counter before entering the sink drain plumbing, this may help the water from coming back inside the dishwasher.
My whirlpool dishwasher model # WDT780SAEM1 makes a loud popping noise when I open and shut the door. What is causing it and how do I fix it?
The loud popping noise that you're hearing when you open and shut the door of your Whirlpool dishwasher (model # WDT780SAEM1) is most likely caused by the door gasket. The door gasket is the rubber seal that runs around the door, creating a tight seal when the door is closed.
Here are a few things you can try to fix the issue:
- Check the gasket for damage: Inspect the door gasket for any tears, cracks, or other damage. If you find any damage, you will need to replace the gasket.
- Clean the gasket: Over time, debris and food particles can accumulate on the gasket, causing it to become stiff and not seal properly. Clean the gasket with a mild detergent and warm water, and then dry it thoroughly.
- Check the door alignment: Make sure that the door is properly aligned and not hitting the gasket when you open and shut it. If the door is not aligned properly, you will need to adjust it.
- Lubricate the hinge: If the door gasket is in good condition and properly aligned, the problem may be with the hinge. Try lubricating the hinge with a silicone-based lubricant, as this can help to reduce friction and noise.
- Contact Whirlpool: If you have tried all of the above steps and are still unable to fix the issue, contact Whirlpool customer service for further assistance. They will be able to provide you with additional troubleshooting steps or advice, or they may need to send a technician to repair or replace the dishwasher.
It's important to note that if the popping noise you're hearing is accompanied by other symptoms, such as leaks, then it may be related to a different problem, and you should contact Whirlpool customer service or a professional service technician for further diagnosis and repair.
1/14/2023 1:48:41 AM •
Whirlpool...
•
Answered
on Jan 14, 2023
Whirlpool gold quiet partner iii soak and scour indicator light on won't start
Es posible que la luz Soak & Clean del lavavajillas Whirlpool Gold Quiet Partner III no se encienda si el lavavajillas no est? recibiendo energ?a o si el lavavajillas no est? en el ciclo correcto. Se recomienda verificar la fuente de alimentaci?n y asegurarse de que el lavavajillas est? enchufado y reciba energ?a. Si la alimentaci?n est? conectada y el lavavajillas est? en el ciclo correcto, entonces es posible que haya un problema con los circuitos o el cableado del lavavajillas. Se recomienda ponerse en contacto con un centro de servicio autorizado de Whirlpool para obtener m?s ayuda.
1/6/2023 2:20:04 AM •
Whirlpool...
•
Answered
on Jan 06, 2023
Updated question - What would cause a Whirlpool Dishwasher DU1148XTPB3 Soap Dispenser's trigger/spring to continuously try to open the soap dispenser after it has been opened.
here are a few possible causes for a dishwasher soap dispenser's trigger/spring to continuously try to open the dispenser after it has been opened:
The trigger/spring mechanism may be damaged or broken. This could be caused by normal wear and tear over time, or it could be the result of a foreign object getting stuck in the mechanism.
The dishwasher's control board may be malfunctioning. If the control board is not functioning properly, it could send a signal to the soap dispenser to continuously open and close.
There may be a problem with the dishwasher's timer or motor. If the timer or motor is not working properly, it could cause the soap dispenser to malfunction.
To troubleshoot the problem, you could try cleaning the soap dispenser and checking for any foreign objects that may be stuck in the mechanism. You could also try resetting the dishwasher by turning off the power and unplugging it for a few minutes, then plugging it back in and turning it on. If these steps do not resolve the issue, it may be necessary to call a professional for further assistance or to consider replacing the soap dispenser.
12/29/2022 3:12:20 PM •
Whirlpool...
•
Answered
on Dec 29, 2022
18" Whirlpool dishwasher humming. What to fix?
Hey, thank you for the question. According to my research the problem is most likely with its Rear Drum Support Roller Kit, part number 349241T. if this is not fixing the problem then the problem is most likely with Idler Pulley, part number WP691366. I hope this will fix your problem.
9/24/2022 4:25:39 PM •
Whirlpool...
•
Answered
on Sep 24, 2022
Whirlpool adp 6515ix dishwasher start button is flashing in 4 time cycles-what does this tell me please. None of the manuals indicate what the flashing could be signalling.
Error CodeConditionCheck/RepairShop PartsClean light blinks 7 timesHeater circuit failure. Control didn't detect the expected rise in water temperature.Check the heating element and related components (wiring and control board) in that circuit.
Heating element, Electronic control board, Thermistor, Circuit wiring
Console light blinks rapidlyThe control detects a stuck button on the control panel.A failed control panel or a malfunctioning electronic control board can cause this code. Check the buttons on the control panel using a volt/ohm meter. In most cases, the control panel must be replaced. If that doesn't solve the problem, the electronic control board might be at fault.
Control panel, Electronic control board
Start/Resume light blinks slowlyIf the dishwasher door is opened or power is interrupted during the cycle, the dishwasher won't start again until the door is detected as closed and the Start/Resume button is pressed.Check the door latch and switch assembly. A failure in the Start/Resume button also can cause this problem.
Door switch assembly, Control panel, Electronic control board
Clean light stays onThe dishwasher won't start a new cycle unless it detects that the door opened after the previous cycle.Turn off power to the dishwasher by shutting off the breaker and restarting. If that does not work, the door switch assembly is stuck and must be replaced.
Door switch assembly
Control lock LED is on but not accepting key pressesAccidentally turned on or control detected keypad problem.Press the Heated Dry key for 5 seconds to turn off control lock feature. If that doesn't work, replace keypad.
Keypad
Sanitized LED blinks at end of cycleControl couldn't confirm that the dishes were sanitized.Check voltage to the dishwasher and the temperature of incoming water. Check the diverter motor, the heater and the OWI/thermistor.
Diverter motor, Heater, Thermistor
8/13/2022 7:21:09 AM •
Whirlpool...
•
Answered
on Aug 13, 2022
Not finding what you are looking for?
