20 Most Recent Whirlpool GU2400XTP Built-in Dishwasher Questions & Answers

0helpful
3answers

Dishwasher will not start

You have a clean light flashing. You need to reset you control. It is activated by a number of different situations. Find the tech sheet for your dishwasher which is normally located under the bottom plate of the dishwasher. If you can not find it give me the model number and I will tell you how to activate the diagnostic test. If you do find it follow the section that says diagnostic test. Then check and makes sure you heater element is operating.
1/8/2021 2:23:12 AM • Whirlpool... • Answered on Jan 08, 2021
0helpful
2answers

Calcium build up removal?????

add dishwasher salt if you live in a hard-water area to prevent calcium build up, and try adding a litre of pure lemon juice to remove the initial crusting, as the calcium is highly alkaline, and the lemon juice, being acidic, neutralises it.
2/1/2019 5:22:26 AM • Whirlpool... • Answered on Feb 01, 2019
0helpful
3answers

Whirlpool dishwasher # quiet partner II

Pushing and holding the 'Heated Dry' button should turn off the light over the padlock symbol and get you going again.
8/26/2018 2:03:39 PM • Whirlpool... • Answered on Aug 26, 2018
0helpful
7answers

Whirlpool gold- quiet partner III

An angel of mercy on another blog posted this solution and it worked for me as well. My Whirlpool Quiet Partner Dishwasher would not work due to the CLEAN light flashing in 7 interval sequences. I followed these steps and my dishwasher is not working perfectly...hope it works for you:

"Well for mine which is a Whirlpool Gold Model # GU2400XTPS3, I found the seq of buttons that I had to push to reset the curcuit board. I think it may of been in this forum somewhere. But I had to push - Sani Rinse, Heated Dry, Sani Rinse, Heated Dry, and then the dishwasher went through it's diagnostic cycle and then after that the light stopped blinking and the dishwasher works great. Supposily, there is a Product Tech Sheet behide the kick panel of every dishwasher, but mine was gone so I had to find the information on the internet. You might want to do a serach for the correct seq of buttons you have to push to reset the curcuit board. If you know for sure that the heating element is bad, you will have to order one. "
5/30/2018 8:33:03 AM • Whirlpool... • Answered on May 30, 2018
0helpful
1answer

Quiet partner II is stuck in cancel/drain mode...

you need a new cycle selector ...or "timer "....
5/30/2018 8:30:59 AM • Whirlpool... • Answered on May 30, 2018
0helpful
1answer

I have a Grohe dish soap dispenser that get clogged-? soap

Dilute the soap you use by 1/3 . this won't affect the soaps ability to clean, but it makes it easier on the dispenser.
1/23/2018 5:03:53 AM • Whirlpool... • Answered on Jan 23, 2018
0helpful
1answer

Warranty extensions

there are several but the consenses seems to be they are not worht the money you pay but you can decide the best thing to do is a google search there are several companies Also call your local repair shops see what they offer
1/22/2018 12:33:46 AM • Whirlpool... • Answered on Jan 22, 2018
0answers
0helpful
1answer

I have a Whirlpool Quickwash

Look at the filter screen to see if anything large got past it and into the pump.
11/29/2017 6:05:16 PM • Whirlpool... • Answered on Nov 29, 2017
0helpful
1answer

Odor will not go away.............

hi there,

i would let you try putting a small can with charcoal in it inside the dishwasher. However, you cant use it for about 1 weeks' time.

Charcoal absorbs trapped smell.

hope this helps.
11/18/2017 5:56:35 PM • Whirlpool... • Answered on Nov 18, 2017
0answers
0helpful
1answer

Inside of dishwasher was dirty after cycle,

Check the food grinder (small blade spins against a screen) in the bottom of the dish washer drain. I found the grinder to be inoperative and clogged which reduced / stopped flow of the wash water. Also, small pieces of clear plastic food wrap can block flow.
9/18/2017 5:39:26 PM • Whirlpool... • Answered on Sep 18, 2017
0helpful
1answer

My whirlpool quiet partner II is not quiet at all.

problem water inlet solenoid ( humming) replace it and you get water
9/9/2017 6:05:12 AM • Whirlpool... • Answered on Sep 09, 2017
0helpful
1answer

Wife found 13yr old whirlpool quiet partner 980

there is a relay on the pcb that controls the power to the solenoid valve, there are a few of them. but it could also be old school washer witch can be dial control this is when you turn a nob to a setting and it slowly goes back to off. if its this its controlled by this and no relays or pcb boards are on the washer classed as analoge.
7/28/2017 3:00:36 AM • Whirlpool... • Answered on Jul 28, 2017
Not finding what you are looking for?
Whirlpool GU2400XTP Built-in Dishwasher Logo

1,262 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4383 Answers

Marvin
Marvin

Level 3 Expert

85240 Answers

Cindy Wells

Level 3 Expert

6526 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Dishwashers

  • Whirlpool Dishwashers

Most Popular Question

warranty extensions

  • Dishwashers
Loading...