Top 20 Whirlpool 24 in. DU1100XTPS Built-in Dishwasher Questions & Answers

0helpful
1answer

Normal + rinse light flashing on dishwasher

it sounds like something has came loose. you have to take the control panel apart and you should find a grey flat plastic cabel about 2 1/2 to 3 inches wide.hook it back up and maybe use some electrical tape to keep it in place and that should fix it.
4/15/2014 6:30:22 PM • Whirlpool 24 in.... • 113 views • 0 helpful votes
0helpful
1answer

Why thermal fuse is blown

If you have no power to your machine and the power is on it is the thermal fuse. If the fuse is blown you will get no power at all. To my understanding after talking to many people the thermal fuse is likely the first thing to go bad on a whirlpool dishwasher. A power surge to your unit would cause the fuse to blow or the control board to go bad.
1/13/2013 6:01:58 PM • Whirlpool 24 in.... • 541 views • 0 helpful votes
0helpful
1answer

I put a dishwasher cleaner in and ran the dishwasher. Now the dishwasher does not run. It is a whirlpool quiet partner II

what is your problem right now or you have fixed it all ready okay
10/1/2012 1:15:40 AM • Whirlpool 24 in.... • 137 views • 0 helpful votes
0helpful
1answer

After the last time I ran the dishwasher there is

Hello, Thank You for using FixYa. I will be helping you today.It sounds like the thermal fuse failed.Open the door remove the screws around the top and flip the control panel open.There is a white fuse with two wires coming from it check it for continuity or jump the two wires together to see if it powers back up. If it does replace the fuse with part #8193762 install the whole kit just follow the directions that come with it.And remember tu turn the power off before checking and installing the fuse.
Thank You and please rate my answer if it was helpful..
6/11/2011 2:41:25 PM • Whirlpool 24 in.... • 113 views • 0 helpful votes
0helpful
1answer

My dishwasher will not drain.

Hi,

Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - Water will not drain outheatman101

3/16/2011 9:57:53 PM • Whirlpool 24 in.... • 258 views • 0 helpful votes
0helpful
1answer

No power to dishwasher

Check to see if your dishwasher has power going to it. If you confirm the power supply is good you likely have a bad fuse. Go to the link if you want to download a video so that you can see how to access and replace the fuse.

Appliance Repair

Appliance Parts
3/18/2011 12:29:44 AM • Whirlpool 24 in.... • 122 views • 0 helpful votes
0helpful
1answer

Where's the junction box to hook up main power

Hi,
Underneath the dishwasher behind the kickplate... usually in the right front corner...

heatman101
1/5/2011 5:32:13 PM • Whirlpool 24 in.... • 68 views • 0 helpful votes
0helpful
1answer

Water does not leave after

Fault in the drain valve/drain pump as it is not draining the water in the cycle. You will need to check the voltage on the drain pump, if present the drain pump must work or is faulty or clogged. Must be removed and cleaned or changed.
If there is no voltage then the program controller is faulty, it must be seen if the fault is minor connection of the driver or a total change.
9/24/2010 4:37:11 PM • Whirlpool 24 in.... • 59 views • 0 helpful votes
0helpful
1answer

New Control Unit not working

i think this machine need a test run on it,i suspect a problem in the circuit and it might have blown the board again.adrian,,
7/13/2010 4:53:12 PM • Whirlpool 24 in.... • 128 views • 0 helpful votes
0helpful
1answer

Motor runs but water does not fill and no

There is a small solenoid on the bottom of the unit that operates a valve between the drain and the rest of the machine. That is probably not changing the valve back to pump inside the machine the motor running you hear is probably draining the machine again. When you run it let it fill then when the motor kicks on watch the drain hose under the sink if it jumps or you can feel water running through it the solenoid needs to be replaced. if you need further clarification I can upload photos tommorrow
6/30/2010 6:12:47 AM • Whirlpool 24 in.... • 91 views • 0 helpful votes
0helpful
1answer

Do Whirlpool dishwashers have a food/grease trap

No there is no grease trap on any dishwashers. Are you having a problem with your machine?
3/28/2010 11:23:37 PM • Whirlpool 24 in.... • 614 views • 1 helpful votes
0helpful
3answers

The stop/cancel light keeps flashing. I

Unfortunately I cannot view the comments from other fixya.com consultants so I am coming in cold on this one.

But it appears you are trying to isolate the problem of why the stop/ cancel light are flashing. I suppose the only solution offered in the user guide is to contact the whirlpool service.

Have you considered if the dishwasher is level and fully secured to the underside of the counter. The door switch needs to be fully engaged (both live and neutral switches) otherwise this model is known to cause faults.

e3279d5.jpg
Wiring diagram is shown above. Not sure how good it is.
YOu can download the service manual from http://www.AllRepairManuals.com/ for $4.95 which has all the details.

5/14/2010 2:37:42 AM • Whirlpool 24 in.... • 162 views • 0 helpful votes
0helpful
1answer

Addendum to problem just posted....

Hi,

This is a problem with the water not heating properly, I have a list of things you can check and instruction on how to reset the control so you can wash dishes again. Let me know if you have questions.

Here is the link to the instructions.

http://www.fixya.com/support/r4628906-flashing_or_blinking_green_clean_light_7
5/8/2010 11:32:12 AM • Whirlpool 24 in.... • 127 views • 0 helpful votes
0helpful
3answers

Wash and rinse cycle do"s not stop, repeats over and over

hELLO THERE:
This is refering to a cycle that does not advance
if it does not advance from one cycle to a nother or if it does not stop doing one cycle
When the cycle doesn't advance, it's probably the timer or a cold-water supply problem: It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer. It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. .
4/18/2010 7:43:37 PM • Whirlpool 24 in.... • 145 views • 1 helpful votes
0helpful
1answer

Pots &pans normal sani cycle lighs

If it is a slow blink on the start button it's something to do with your door switch. If it's a rapid continous flashing it's prob a short in your key pad. If it flashes 7 times, pauses and then repeats you have a fault with your heating element.
If it's a short with your key pad and the unit has water in it - stopped mid cycle you can cut the power to the unit at the breaker, open the door controls up and disconnect the 14 pin key pad connection. There should be a wiring diagram in the toekick cover (at the floor). This diagram will tell you how to do various tests, disconnect the key pad. If your not a handy type person call a repair man and tell him you think youhav a short in your key pad.
3/11/2010 3:43:15 PM • Whirlpool 24 in.... • 367 views • 0 helpful votes
0helpful
1answer

Does not empty. water in bottom is dirty. Dishes

Hi,
Here is a tip that I wrote that will help you with your problem...

http://www.fixya.com/support/r4078724-dishwasher_problems_water_will_not_drain

heatman101
4/17/2010 6:31:17 PM • Whirlpool 24 in.... • 131 views • 0 helpful votes
0helpful
1answer

Hooking up a drain line

Connect directly to your existing drain lines under the sink or to your disposal unit.

If you do not have a dishwasher drain adapter on your drain lines the local home center will help you. Install above your S trap. Cut just enough of the pipe out to allow for the new part to slip in (half and inch or so goes into the fitting). You will need glue and primer.

If you connect to your disposal there is a fitting on the side of the disposal to accept the drain line. You should have a fitting supplied with the disposal. If not the local part supplier can help you. Break out the tap on the disposal and connect the fitting and drain line.


Hope this helps. Please rate the answer if it helps you.
3/10/2010 8:45:29 PM • Whirlpool 24 in.... • 264 views • 0 helpful votes
0helpful
1answer

Clean light flashes off and on continually,

Hello- This pump system has a strainer and screen that can trap debris against the pump blades, stopping motor. Turn off power. Pull torx screws holding pump cover and strainer. Remove and clean out debris. Check to see if motor turns. If not, it is locked up and needs to be replaced. Let me know if this info helps- have more if needed. -Thanks- ED
3/7/2010 6:55:47 AM • Whirlpool 24 in.... • 116 views • 0 helpful votes
0helpful
1answer

Du1100xtpq7 dish washer keep repeating wash cycle

Hi


Thanks for using FixYa. If the cycle doesn't complete, check these:
Water-heating cycle
Many dishwashers heat the wash and/or rinse water to a higher temperature, as the cycle calls for it. In these cycles, the dishwasher pauses after it has filled with water, waiting for the water to reach the pre-set temperature. What happens next depends, as follows:

On some units, the pause is timed and the unit continues after the allotted time.

On others, the cycle can't continue until the water reaches the higher temperature. If you have this type of dishwasher and the water isn't being heated (say, because of a problem with the heating element or thermostat), after the unit stops at the heating cycle, it never continues. When you repair the heating-system problem, the "cycle problem" is fixed too.

Timer
Timers don't often fail. But if every other part of the dishwasher seems to be working properly and the timer knob seems to be stuck in one place--doing one function continuously--the timer may be at fault. Dishwasher timers can't be repaired. If yours is defective, replace it.


Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee


1/7/2010 3:02:12 AM • Whirlpool 24 in.... • 435 views • 1 helpful votes
0helpful
2answers

Du1100xtpq7 has had the touch

i would guess that you are having a problem with the optical sensor inside the pump housing. it is suppose to sense when the water is clean or dirty and allow the unit to continue washing or advance to the next cycle.
i have seen these test good but be just out of calibration enough to cause long run times.
you can try to change it yourself or have the service company try that instead of a new board and panel.

1/7/2010 3:18:47 AM • Whirlpool 24 in.... • 355 views • 0 helpful votes
Not finding what you are looking for?
Whirlpool 24 in. DU1100XTPS Built-in Dishwasher Logo

110 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Oloyede Monsuru

Level 3 Expert

1468 Answers

Mike

Level 3 Expert

4377 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Dishwashers

  • Whirlpool Dishwashers

Most Popular Question

whirlpool dishwashers food grease trap

  • Dishwashers
Loading...