20 Most Recent Whirlpool LSN1000LW Top Load Washer Questions & Answers


hello,

what this f 65 code mean is an indication of loose of wire from the sensor reader from the connection

And the PE means that power error that is the loose wire will not allow the washer to carry out is function properly

what you need to do to fix up the problem is to unscrew (OPEN)the WASHER then trace the wire down to the power supply and also the panel connected to the screen clean all form of dirty and water on it fix up the wire that are disconnected from there position .

thank you and thank for using fixay.

Whirlpool... | Answered on Sep 30, 2015


Had same problem with my washer. Check to see if there are little plastic tags holding top/bottom of agitator. after replacing dogs just ensure that you realign with tags so they do not break off.

Whirlpool... | Answered on Jun 26, 2014


Yor drum bearings are faulty and nee replaced Quite an expesive repair

Whirlpool... | Answered on Oct 07, 2013


Hi, If this is a two piece agitator, start the wash cycle with no laundry in it and see if the lower half of the agitator moves. If the lower half works, you will need to change the dog kit inside the agitator. There is a 7/16" bolt under the agitator cap the will need removed to get the agitator out.
If the agitator does not move at all, It could be the coupler connecting the transmission to the motor. If the coupler is bad, tub will not spin the laundry dry.

I hope this helps you. Please let me know if I can assist you further.

Vic

Whirlpool... | Answered on Sep 12, 2012


Hi, My guess is that the belt has come off or broken. Replace it. Good luck.

Whirlpool... | Answered on Jun 24, 2011


This is a clear evidence of a broken lid switch. Power to the drive motor is routed through the lid switch. The machine, therefore, will not turn on when the lid switch is not working. Manually activate the lid switch and if still doesn't work, bypass the lid switch. Disconnect power then jump a wire between the outer terminals of the disconnected connector from the cabinet top then reconnect power. Replace the lid switch to address the problem if the machine works with the lid switch bypassed.

Release the console from the top of the cabinet depending on the model of your machine then pull forward and up on the console and lay it back on the hinges.
jahn27_7.jpg
jahn27_8.jpg
jahn27_9.jpg

Disconnect the lid switch harness connector by pressing on the tab located in the middle and pulling it up.
jahn27_10.jpg

The cabinet is attached to the rear of the washer by two brass-colored retaining clips. Insert a flat blade screwdriver into the turned-up edge of the clip, located on both sides, and then pry back to release the clip from the slot in the cabinet.
jahn27_11.jpg

Open and hold the lid while grabbing the cabinet front opening then tilt the top of the cabinet toward you by pulling the cabinet away from the base. This releases the front and back slots of the cabinet from the tabs in the front and back of the base.
jahn27_12.jpg

Using the side of your leg and/or body as a support for the front of the cabinet, carefully lift up the cabinet and lay the front on a cushioned floor to access the lid switch.
jahn27_13.jpg

Remove the lid switch ground and mounting screws then release the wire harness from the metal retainers. Pull the lid switch connector out and install the new lid switch in reverse order of the removal steps.
jahn27_14.jpg

Bring the cabinet to the front of the washer then slide the front bottom rail of the cabinet under the rail at the base of the machine then lay down the cabinet into position. Make sure the slots in the cabinet sit into the tabs at the base of machine.

Reconnect the lid switch harness then push the retaining clips back down into position to secure the cabinet to the rear of the machine. Reinstall and secure the console to complete the repair.


Whirlpool... | Answered on Nov 09, 2010


Check the lid switch.

Whirlpool... | Answered on Nov 01, 2010


water valve for sure replace and you will be fine

Whirlpool... | Answered on Oct 27, 2010


Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101

Whirlpool... | Answered on Oct 02, 2010


If you enter your model# at the link provided you will be able to pull up diagrams and illustrations. This type of washer is supposed to have the front housing pulled off to gain acess. The link provided will also have a video that walks you thru the correct procedure for Disassembling a whirlpool style washer

Whirlpool... | Answered on Sep 27, 2010


Super cap 27" Imperial Series 3.2 cu. ft. capacity washer with a three-speed motor. How it works: Direct Drive washer

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Whirlpool... | Answered on Sep 27, 2010


verify hot to hot and cold to cold hose hookups and that BOTH are on.

Whirlpool... | Answered on Sep 06, 2010


It sounds to me as if the shipping restraints on the machine tub are still in. If so you will need to remove them. using the machine with them in will severely damage the transmission and tub assembly. This will also void the warranty. Go through your manual to be sure they have all been removed. If they have then check to ensure that the machine is level. If so then you may have a defective unit and need to contact the store that you purchased it from and discuss a refund or swap out. Hope this helps. Good luck.

Whirlpool... | Answered on Sep 05, 2010


If it works correctly all the way to the spin cycle the does nothing, its a 90% chance you have a ( Bad or Broken ) LID switch.. FOR SAFETY REASONS they design top load units so that they will not spin if the switch is bad .Gently lift up the lid a few inches then lower to close ,most of the time you should be able to hear a clicking sound when the lid is opened and closed if the switch is working properly,if no sound YOU NEED A LID SWITCH and easy item to replace Good luck

Whirlpool... | Answered on Aug 30, 2010

Not finding what you are looking for?
Whirlpool LSN1000LW Top Load Washer Logo

104 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

18455 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Washing Machines

  • Whirlpool Washing Machines

Most Popular Question

trying find

  • Washing Machines
Loading...