20 Most Recent HP LaserJet 600 M602DN Laser Printer - M - Page 3 Questions & Answers

This sounds serious. Maybe you should get the experts in.

HP Office... | Answered on Aug 20, 2020

There are several error that could be in your Hp printer that's why your HP printer is unable to print such as paper jam, print jobs stuck in queue and other printing problems etc.
To troubleshoot HP printers Visit https://www.printeralign.com/fix-hp-printer-wont-print

HP Office... | Answered on Aug 11, 2020

This error (supply memory error) usually comes up when there is a bad contact between the cartridge's chip and the printer. Sometimes that chip becomes faulty. If you have replaced the corresponding cartridge and you still get the same error then you will have to look at the printer's side which makes the contact to that chip.

HP Office... | Answered on Jul 24, 2020

If you have already replaced the paper feed motor once then you are supposed to replace it again and also replace an additional part I have listed the part numbers below.
Motor, paper feed assembly (M101) (HP Part #: RM1-8285-000CN)
Paper Feed Roller Assembly (HP Part #: RM1-8411-000CN)
The motor would have failed the second time because the other part was too tight and hard to drive which would have resulted in an overcurrent condition.

HP Office... | Answered on Jul 23, 2020

There are a few common HP printer Problems:
1. Streaks through printing - Clean printhead using windex and alcohol swabs.
Run a "clean printhead cycle"
2. Paper jams: Check all paper paths using a flashlight. Remove rear cover or duplexer to get more access. Even a tiny piece of a paper or another object can disrupt the printer functionality.
3. Skewed printing -
Check for the duplex unit or paper path to be fully inserted on both sides. If skewed printing only appears when making a copy, the scanner lamp is misplaced or out of rail.
Paper will not feed.
Try cleaning the paper pick up roller with some cleaning solution or alcohol swabs. Usually does the trick!
Good luck! HP is a good printer.

HP Office... | Answered on Jul 14, 2020

If you are looking for an affordable HP laser Printer repair in Manhattan then take the help of this information and get in touch with a certified third-party expert. We repair your printer and this might even take a few days as well. Hence, we hope that you get the best service by our printer technician expert for your printer.
Contact us : +1(802)722-2574
or for details you can visit to our website :https://www.instanttfn.com/blog/hp-printer-technician-repair-in-manhattan

HP Office... | Answered on Jun 11, 2020


Hp Printer Error "Carriage cannot move paper jam" when non exists.

Hp Printer Error "Carriage cannot move paper jam" when non exists.

The printer made strange noises this week. Assuming you are certain there is no paper jam and tipped the printer upside down as well. You have an error that leaves the print heads in the middle near the middle or left or right.

This is for you. "Carriage cannot move paper jam"

Whats happening is the print heads slide and are moved by a motor and belt.
To know whereabouts the print head is there is a resistance strip.
This is a strip of what looks like old real to real magnetic tape.
Its stretched as a strip in line with the print heads and is hidden from view.

Under the plastic see Arrow, is the location of this strip.

A sensor similar to a magnetic tape head which reads its position.

look at the image and just below this you will feel it. Clean this length of tape with some nail varnish cleaner and a non lint cloth.

You can slide the print head to clean the hole length.Your pint head will now position and park correctly.


on Jun 10, 2020 | HP Office Equipment & Supplies

Check in your device manager list to uninstall any listed as not installed properly then rerun the setup program. Only plug the printer usb in when the program prompts you.
The noise is normal as the printer is seting the head position and cleaning the print head, it is also running the rollers to check if there is a paper blockage or any paper in the load tray.

I get to the device manager by using the explorer for windows files, then on the Left side where the hard drivers are listed right click on This PC, choose properties.
A new screen will open that is labelled System.
On the top left you will see Device Manager.

Hope that helps :)

HP Office... | Answered on Jun 10, 2020

Printer Offline Error on the desktop screen shows that it failed to communicate with HP Officejet 3830 printer. The printer offline error mainly occurs due to a faulty driver, if you are facing any problem with your HP OfficeJet 3830, then you must follow these Steps to fix Officejet 3830 Printer Offline Error.

HP Office... | Answered on Jun 07, 2020

If your printer's status displays "Printer in error state," there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn't open and the paper isn't jammed

HP Office... | Answered on Jun 01, 2020

Usually, Error Code 0x07a74dd6 occurs when users try to start printing via connection to the computer. The Error Code 0x07a74dd6 could refer to anything from the product needing a basic reset to reinstalling the printhead or cartridges.

HP Office... | Answered on May 29, 2020

How to Completely Delete and Uninstall the HP Printer Deskjet Driver Software. HP printers ship with several printing applications and drivers.

HP Office... | Answered on May 29, 2020

First, be sure all four toner cartridges are seated properly as is the transfer belt. Close the front panel, then the top panel, power-cycle the printer and try again. If that doesn't solve the issue, it sounds as if either the actuator for the front door switch is broken off (which is highly unlikely) or the door switch itself is out of position. Getting to the switch involves removing most of the panels just to get to it; not impossible, just involved and a LOT of screws, plus a small black spacer for the top-left panel hinge. If you have any kind of a warranty or maintenance agreement on the printer, DO NOT TRY THIS, you WILL void it!! You have to unplug the printer, remove the fuser from up top, then the top panel, lower the front panel and remove the transfer belt and keep it out of the way in a dark area. Remove the hinged rear panel at the rear bottom followed by the rear panel (which fits inside a side panel, something to remember when reassembling). Now the side panel. If the switch is out of position, reposition it. If it's broken, it will need to be replaced. Reassembly is in the EXACT opposite of disassembly. You may wish to forego this and get an HP authorized tech in to do this for you. Worst Case Scenario: the DC Controller board is bad. But that's also unlikely ... possible, but unlikely. Let me know how it turns out!

HP Office... | Answered on May 24, 2020

go to start menu, choose printer & faxes, click the printer icon properties and find the printer resolution to adjust the dark printing capability

HP Office... | Answered on May 24, 2020

Not finding what you are looking for?
HP LaserJet 600 M602DN Laser Printer - M Logo

27 questions posted

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts


Level 3 Expert

1997 Answers

Cindy Wells

Level 3 Expert

6185 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

HP Office Equipment & Supplies

  • HP Office Equipment & Supplies

Most Popular Question

fuser error printer 50 92 11

  • Office Equipment & Supplies