HP ProLiant ML370 G4 Server - Answered Questions & Fixed issues


It may be that the lithium battery is dead; usually a CR2032 button battery. Signs of CMOS Battery Failure Dom Tech Computer Blog

Go into the BIOS settings during initial power on boot up, often F10 or F2 are common. Check the date and time, if they are off, you should be able to temporarily boot by setting the date and time but you'll have to do it every time you boot. If the date and time is off, and you set the correct date and time and it still doesn't boot, you'll want to make sure it's booting to the correct drive.

When it doesn't boot, does it give you any error?

HP ProLiant... | Answered on Jul 04, 2017 | 198 views


Go into BIOS and remove the Stop on Error on Boot selection.

HP ProLiant... | Answered on Aug 10, 2014 | 57 views


Reset NVRAM using SW6 switch ( Maintainance Switch )

HP ProLiant... | Answered on Oct 25, 2013 | 82 views


update to latest BIOS

HP ProLiant... | Answered on Oct 25, 2013 | 353 views


Clean Dust inside the server & update with latest bios ,room temperature should be 18 degree Celsius

HP ProLiant... | Answered on Oct 25, 2013 | 318 views


Run Chkdsk / recreate Raid & reinstall OS

HP ProLiant... | Answered on Oct 25, 2013 | 39 views


check & set the boot controller order in BIOS

HP ProLiant... | Answered on Oct 20, 2013 | 152 views


Hi ,,

did you tried the offline diagnostics tools (Array Diagnostic Tool) and check it .

HP ProLiant... | Answered on Mar 23, 2013 | 54 views


Open the case and turn on. There should be a corresponding led lit inside. That, or you could run Insight Manager. It will tell you exact details.

HP ProLiant... | Answered on Mar 01, 2013 | 430 views


You will continue to get internal error until you add memory. It shouldn't even boot without RAM.

HP ProLiant... | Answered on Feb 04, 2013 | 1,024 views


This is because either the image on the hard drive is bad (corrupted, missing boot sector, etc) or because the hard drive itself has some issue like corruption etc.
If this is a mirrored raid array (two drive mirroring each other) I would try to remove one of the drives and boot again. If that does not work reinsert and remove the other drive and try to boot.

regards,
Mike

HP ProLiant... | Answered on Oct 26, 2012 | 353 views


Use the HP Smartstart CD and configure the with array with 2 arrays and 2 logical drives. The first with OS array on RAID 1 (2 drives mirrored). The second array on RAID 5 (3 drives minimum).


http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18964&prodSeriesId=345557&prodNameId=344318&swEnvOID=1005&swLang=8&mode=2&taskId=135&swItem=MTX-bd347636805e4917a617382469


Make sure to use Insight Manager for worry free monitoring.

HP ProLiant... | Answered on Oct 22, 2012 | 124 views


Replace HDD (Red Flashing ).It seems you have unknowingly disturbed your Raid . If Possible take backup of your server.Reconfigure RAID and Freshly Install OS .

HP ProLiant... | Answered on Apr 11, 2012 | 384 views


I'd say the hard disk went bad. See if it'll boot from a live cd to copy your data off of the linux drive (if it's accessible at all).

HP ProLiant... | Answered on Dec 30, 2010 | 356 views


The setup program does not recognise your storage controller.

HP and Dell usually supply a startup CD, that will help you configure RAID levels and partitions and start the Windows installation. If you have the supplied CD boot from it and it should work OK, if not you can download it here

http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=15351&prodSeriesId=316541&prodNameId=327476&swEnvOID=1005&swLang=8&mode=2&taskId=135&swItem=MTX-d7672226b6284520b9e292b9bd

Please let me know if it works, any issues send a reply :)

HP ProLiant... | Answered on Dec 22, 2010 | 344 views


dear erwin,

as per your writing the server raid has broken .. its may be a problem with a hard disk , first you have to check the hard disk state . to do that you should enter into raid bios . don't try to something on that , just see the status of logical drive then which are the disks includes on that raid

in you post also it may give the details of failed disk ids

then you may have problem with your batt. unit , for that please do the above steps first then back with that...

HP ProLiant... | Answered on Aug 11, 2010 | 602 views


Hello,

The best way to connect is to use the Ethernet cable to connect each pc to each other or use a Ethernet hub to connect the two together.

Good Luck
C2S

HP ProLiant... | Answered on May 28, 2010 | 211 views


Restart Computer and during the POST self test phase, press either F10, DEL, or sometimes F8. Press only one key per start. Usually one of the three will work.

HP ProLiant... | Answered on Mar 31, 2010 | 232 views


Restart ur computer .
Press DEL , F10 or F8
U can try with all the three keys
And it will redirect u to the BIOS setup
It depends on wats the brand of the motherboard ?
If u can tell me wats the brand of the motherboard i can tell u wat exactly u need to do.



HP ProLiant... | Answered on Nov 25, 2009 | 516 views

Not finding what you are looking for?
HP ProLiant ML370 G4 Server Logo

39 questions posted

Ask a Question

Usually answered in minutes!

Top HP Computers & Internet Experts

Lee Hodgson
Lee Hodgson

Level 3 Expert

4810 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

efs_perpends
efs_perpends

Level 3 Expert

1997 Answers

Are you a HP Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...