20 Most Recent Whirlpool AWM5125/1 Front Load Washer Questions & Answers


Go to the Whirlpool web site, click on support, then select Instructions for Use (or Manuals & Literature, whatever... it should be obvious.) This will take you to a page where you type in the model number for your machine. After a quick search you will be able to download the .pdf file containing the instructions.

Whirlpool... | Answered on Sep 27, 2019


the rubber on the door has got a hole

Whirlpool... | Answered on Mar 31, 2019


Are you in the UK? It sounds like the door is ajar or a faulty door assembly. Check that the water is turned on or that the hoses aren't kinked.

Whirlpool... | Answered on May 03, 2014


Sounds like you have a blockage of sorts .Remove clean soap dispenser /check water pressure not too high

Whirlpool... | Answered on Mar 20, 2014


you might try. laundry.manualsonline.com

Whirlpool... | Answered on Nov 19, 2013


Possibly the pump rotor is jammed. Try dismantling the pump and cleaning it out.

Whirlpool... | Answered on Nov 01, 2013


Most likely you need to replace the motor control board. You may need a serviceman to confirm this issue.

Whirlpool... | Answered on Oct 22, 2013


Just go to the whirlpool web site and search for it. Click on Service, then Instructions & Literature.

Whirlpool... | Answered on Oct 21, 2013


i'm going to start at the beginning-disconnect water supply from machine-run each one into bucket or wash tub to make sure supply is good and strong-make sure the little screens in the machine water valve(this is where you connect the hoses) are clean-if they have had build up(rust-scale) and machine still doesn't fill you have a bad water valve-replacing it is relatively easy-cheers Denny

Whirlpool... | Answered on Oct 20, 2013


remove the top cover by removing the two screws at the top back portion of the unit.

slide back the top cover.

inspect the location of the soap and fabric conditioner dispenser. if it has three solenoids or two solenoids, maybe one of the solenoid is malfunctioning that is why it is not dispensing the fabric conditioner.

if it is a cable type, inspect the cable as it runs to the mechanical timer.
make sure that the cable is not broke and it is strecht as it should be.

check the mechanical timer if the cable holder is in place in the mechanical switch.

i hope i was able to help and solve ur problem,

tnx 4 using fixya,

drcool

Whirlpool... | Answered on Aug 06, 2013


I assume your talking about the drain filter. If you are you would open the small access panel located down the bottom of the unit and turn the filter to the left in counter clockwise direction. It is best to have a small pan and a shop vac in place to vacuum up the water that will come out of this area. Note sometimes when the filter is stuck you can use a screwdriver across the two tabs to turn the filter. If you have any further questions message me back. Thanks again Rick

Whirlpool... | Answered on Aug 27, 2012

Not finding what you are looking for?
Whirlpool AWM5125/1 Front Load Washer Logo

120 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Washing Machines

  • Whirlpool Washing Machines

Most Popular Question

no water going in machine filter clear

  • Washing Machines
Loading...