Top 20 OKI C5800dn Laser Printer - Page 2 Questions & Answers


there is pickup roller for picking up paper see that clene it and replace it if needed.

OKI C Office... | 197 views | 2 helpful votes


RESET OKIDATA TONER DRUM 1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

All toner, drum, fuser and transfer figures return to 100\%.

OKI Office... | 49 views | 0 helpful votes


sounds like the printer heads needs to be clean or a paper jam.

your printer should have came with self cleaning software

paper jam
remove paper tray, open all access to printer to check if there is a crumbled paper or even a small torn piece of paper from a previous jam.

if successful restart your printer

OKI Office... | 78 views | 0 helpful votes


in case you need it ....The Administrator log in for the menus s :admin pw: aaaaaa

your answer is here:
http://www.manualslib.com/manual/916780/Oki-Mc361.html?page=19

OKI Office... | 100 views | 0 helpful votes


Error code 122 means " Low voltage FAN error ".

Is the FAN (bottom right of the front) of the low voltage power supply block working? Is the FAN connector connected correctly?

Check to make sure connection of the FAN connector. Replace the low voltage power supply unit. Replace the FAN motor. Replace the low voltage power supply unit.

Source: https://www.okoki.co.uk/how-to-fix-oki-printer-error-codes

OKI Office... | 35 views | 0 helpful votes


Sometimes if there was a paper jam and someone removed it without getting all of the paper, then there could be a small piece of paper still in the way of the sensor. If you have any compressed air it might help to blow it out of the sensor area. I have had issues with that in the past as well, so I opened up the area it said it was jammed - gave it a good going over with the can of compresses air, and it seemed to clear out the jam.

OKI Office... | 72 views | 0 helpful votes


power down the printer for 30 minutes. remove and then insert the magenta toner. power on.

OKI Office... | 297 views | 0 helpful votes


It could be a re-allocation of IP address. The best solution to that is to allocate the printer a specific permanent IP address and but the same setting into the port address for the machine on every PC using it

OKI Office... | 84 views | 1 helpful votes


Please feel free to contact our customer service number +1-(845)-477-5334 to fix all Oki Fax product related issues

OKI Office... | 59 views | 0 helpful votes


The printer seems to have both USB and ethernet connections therfore any PC or Mac should be able to connect without any problem. You will need to install the compatible driver for your peeing system. This can be found on the manufacturer website. Hope it helps

OKI Office... | 37 views | 0 helpful votes


980

An error occurred like paper curling to the fuser unit.

OKI Office... | 304 views | 1 helpful votes


You cant find the reset because there is not one. OKI do not use resets to cure errors. Yes a 980 is paper wrapped around the hot or pressure rollers in the fuser. Normally you just take out the fuser and remove the paper and it will start working. However this MUST be done with the power OFF. So it should be a case of just turning it off and removing the jam and refitting the fuser and turning it back on. If the error is still there then alas a new fuser is require to get it going again. You may be able to buy a fuse from suppliers on the net, fit it and that will do the reset without the need of buying a fuser.

OKI Office... | 351 views | 0 helpful votes


The only thing in common with both of the printers is the USB cable you are using. Try another one.

OKI Office... | 70 views | 0 helpful votes


231 Is a RFID error. I have seen this a few times and can be caused by rf interference. If you have any electrical device sitting very close (ie router/pc/hub/media centre/microwave etc. This will cause a 231 error.

OKI Office... | 164 views | 0 helpful votes


Have seen this before and its probably used on an extension lead. Although the led on the extension may be lit, there is no power to the actual socket. try plugging straight into a known working wall socket. Have you tried another mains lead?

OKI Office... | 62 views | 0 helpful votes

Not finding what you are looking for?
OKI C5800dn Laser Printer Logo

17 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top OKI Office Equipment & Supplies Experts

Alvin Barnabas
Alvin Barnabas

Level 2 Expert

134 Answers

Timothy Van Der...

Level 2 Expert

152 Answers

Mike

Level 3 Expert

4372 Answers

Are you an OKI Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

C OKI

  • C OKI

Most Popular Question

oki c5800 printer sensor malfunction

  • Office Equipment & Supplies
Loading...